Index - Siemens SINUMERIK 828D Funktionshandbuch

Index

$
$A_DP_IN_CONF, 63
$A_DP_IN_STATE, 64
$A_DP_IN_VALID, 64
$A_DP_OUT_CONF, 63
$A_DP_OUT_STATE, 64
$A_DP_OUT_VALID, 64
$A_IN, 36
$A_INA, 36, 43
$A_INCO, 50
$A_OUT, 36, 38
$A_OUT[n], 649
$A_OUTA, 36, 45
$AA_ACT_INDEX_AX_POS_NO, 873
$AA_COUP_ACT, 819
$AA_COUP_OFFS, 819
$AA_ENC_COMP, 291
$AA_ENC_COMP_IS_MODULO, 291
$AA_ENC_COMP_MAX, 290
$AA_ENC_COMP_MIN, 290
$AA_ENC_COMP_STEP, 290
$AA_FIX_POINT_ACT, 191
$AA_FIX_POINT_SELECTED, 191
$AA_ISTEST, 392
$AA_MOTEND, 722
$AA_PROG_INDEX_AX_POS_NO, 873
$AC_AXCTSWA, 114
$AC_AXCTSWE, 114
$AC_FIFO, 542
$AC_ISTEST, 392
$AC_RETPOINT, 787
$AN_AXCTAS, 114
$AN_AXCTSWA, 114
$AN_CEC, 298
$AN_CEC_DIRECTION, 299
$AN_CEC_INPUT_AXIS, 298
$AN_CEC_INPUT_NCU, 299
$AN_CEC_IS_MODULO, 300
$AN_CEC_MAX, 299
$AN_CEC_MIN, 299
$AN_CEC_MULT_BY_TABLE, 300
$AN_CEC_OUTPUT_AXIS, 298
$AN_CEC_STEP, 298
$AN_LAI_AX_IS_AXCTAX, 114
$AN_LAI_AX_IS_LEADLINKAX, 114
$AN_LAI_AX_IS_LINKAX, 114
$AN_LAI_AX_TO_IPO_NC_CHANAX, 114
Erweiterungsfunktionen
Funktionshandbuch, 08/2018, 6FC5397-1BP40-6AA2
$AN_LAI_AX_TO_MACHAX, 114
$AN_REBOOT_DELAY_TIME, 372
$P_COUP_OFFS, 820
$P_GWPS, 915
$P_ISTEST, 392
$TC_DP1, 888
$TC_DPC1...10, 888
$TC_TPC1...10, 894
$TC_TPG_DRSPATH, 894
$TC_TPG_DRSPROG, 894
$TC_TPG3, 892
$TC_TPG4, 892
$TC_TPG5, 892
$TC_TPG8, 892
$TC_TPG9, 893
$VA_COUP_OFFS, 819
1
1-dimensionale
Sollwertvorgabe ($AC_MEAS_TYPE = 19), 592
2
2-dimensionale
Sollwertvorgabe ($AC_MEAS_TYPE = 20), 593
3
3-dimensionale
Sollwertvorgabe ($AC_MEAS_TYPE = 21), 595
3D-Messtaster, 559
6
6FC5800-0AM28-0YB0, 467
A
Abrichten, 898
Achs
-interpolator, 706
Achscontainer
-Bezeichner, 105
Achse
Basis-, 285
Kompensations-, 285
953