Grundfos Control MPC Montage- Und Betriebsanleitung Seite 583

Nastavak sa stranice 582
4. Settings
4.1 Primary controller
4.1.1 PI controller
4.1.2 Alternative setpoints
4.1.2.1
4.1.3 External setpoint influence
4.1.3.1
4.1.4 Primary sensor
4.1.6 Clock program
4.1.7 Proportional pressure
4.1.8 S-system configuration
4.1.9 Setpoint ramp
4.2 Pump cascade control
Min. time between start/stop
4.2.1
Max. number of starts/hour
4.2.3 Standby pumps
4.2.4 Forced pump changeover
4.2.5 Pump test run
4.2.7 Pump stop attempt
4.2.8 Pump start and stop speed
4.2.9 Min. performance
4.2.10 Compensation for pump start-up time
4.3 Secondary functions
4.3.1 Stop function
4.3.1.1
4.3.3 Soft pressure build-up
4.3.5 Emergency run
4.3.7 Digital inputs
4.3.8 Analog inputs
Setting, AI1 (CU 352), [51] - AI3, [51, 54, 57]
Setting, AI1 (IO 351-41), [57] - AI2 [57, 60]
Setting, AI1 (IO 351-42), [57] - AI2 [57, 60]
4.3.9 Digital outputs
DO1 (CU 352), [71] is signalling - DO2 [71, 74]
DO1 (IO 351-41), [77] is signalling - DO7 [77 - 88]
DO1 (IO 351-42), [77] is signalling - DO7 [77 - 88]
4.3.10 Analog outputs
AO1 (IO 351-41) [18] - AO3 [18, 22, 26]
AO1 (IO 351-42) [18] - AO3 [18, 22, 26]
4.3.14 Min., max. and user-defined duty
4.3.14.1 Min. duty
4.3.14.2 Max. duty
4.3.14.3 Set user-defined duty
4.3.19 Pump curve data
4.3.23
4.3.20 Control source
4.3.22 Fixed inlet pressure
4.3.23 Flow estimation
4.3.24 Reduced operation
4.4 Monitoring functions
4.4.1 Dry-running protection
4.4.1.1
4.4.1.2
4.4.1.3
4.4.2 Min. pressure
4.4.3 Max. pressure
4.4.4 External fault
4.4.5 Limit 1 exceeded
4.4.6 Limit 2 exceeded
4.4.7 Pumps outside duty range
4.4.8 Pressure relief
4.4.9 Log values
4.4.10 Fault, primary sensor
4.5 Functions, CU 352
Change language to the service language (English)
Run wizard again
4.5.1 Display language
4.5.2 Units
4.5.2.1
4.5.2.2
4.5.2.3
4.5.2.4
4.5.2.5
4.5.2.6
4.5.2.7
Alternative setpoints 2 - 7
Input value to be influenced by
4.1.3.2 Setting of influence function
Stop parameters
Function, DI1 (CU 352) - DI3, [10, 12, 14]
Function, DI1 (IO 351-41) - DI9, [10 - 46]
Function, DI1 (IO 351-42) - DI9, [10 - 46]
Function, AI1 (CU 352) - AI3 [51, 54, 57]
Function, AI1 (IO 351-41) - AI2 [57, 60]
Function, AI1 (IO 351-42) - A2 [57, 60]
Flow estimation
Pressure/level switch
Measurement, inlet pressure
Measurement, tank level
Pressure
Differential pressure
Head
Level 4.5.2.8 Temperature
Flow rate 4.5.2.9 Power
Volume 4.5.2.10 Energy
Specific energy
4.5.3 Date and time
4.5.4 Password
4.5.5 Ethernet
4.5.6 GENIbus number
4.5.9 Software status
583