Storz NAV1 pico Gebrauchsanweisung Seite 205

2
Inhalt
Anschließen an die serielle
Kommunikationsschnittstelle ............................25
Anschließen eines Fußschalters .......................25
Anschließen des Navigation Base Unit
an einen externen Monitor ...............................26
Anschließen des Navigation Base Unit
an eine Videoquelle ..........................................26
Durchführen der Planung
mit dem NBU-Navigationssystem .......................28
Einschalten des NBU-Moduls ..........................28
Starten der Planungssoftware ..........................28
Einlesen von Patienten-Bilddaten .....................32
Einlesen von Patienten-Bilddaten
von einer lokalen Festplatte ..............................32
Einlesen von Patienten-Bilddaten
von CD/DVD ....................................................32
Einlesen von Patienten-Bilddaten
von USB ..........................................................33
Einlesen von Patienten-Bilddaten
vom PACS .......................................................34
Einstellen des Netzwerkzugangs ......................34
PACS-Konfiguration .........................................34
Einlesen von Patienten-Bilddaten .....................35
Suche nach bestimmten Patientendaten ..........35
Auswahl des Patienten .....................................36
Anpassen des Oberflächenkontrasts ................38
Verwendung eines fusionierten Datensatzes
von CT und MRT ................................................39
Wichtige Fakten für die Fusion
von CT und MRT .............................................39
I. Importieren von CT-Bilddaten ........................40
II. Importieren von MRT-Bilddaten ....................40
Darstellung der Fusion .....................................40
Abrufen zuvor geladener Daten ........................41
Positionierung von Landmarken für
die Patientenregistrierung ...................................41
Generelle Hinweise zur Positionierung
von Landmarken ..............................................41
Hinzufügen und Verschieben von
Landmarken im 3D-Oberflächenmodell ............43
Hinzufügen und Verschieben von Landmarken
in den zweidimensionalen CT-Schnitten ...........44
Anpassung der Darstellung von Patientendaten .45
Auswahl des Fensterinhalts ..............................45
Vergrößern, Verkleinern und Verschieben
der Schichtdarstellung .....................................46
Weichzeichnen der Schichtdarstellung .............47
Contents
Connecting to serial
communication ................................................25
Connecting a footswitch ..................................25
Connecting the Navigation Base Unit
to an external monitor ......................................26
Connecting the Navigation Base Unit
to a video source .............................................26
Carrying out planning with the NBU
navigation system ...............................................28
Switching on the NBU module .........................28
Starting the planning software ........................28
Reading in patient image data ........................32
Reading in patient image data
from a local hard disk ......................................32
Reading in patient image data
from CD/DVD ...................................................32
Reading in patient image data
from USB .........................................................33
Reading in patient image data
from PACS .......................................................34
Setting up network access ..............................34
PACS Configuration .........................................34
Reading in patient image data .........................35
Searching for specific patient data ...................35
Selecting the patient ........................................36
Adjusting the surface contrast..........................38
Using a fusion data record
from CT and MRI ................................................39
Important facts for CT and
MRI fusion........................................................39
I. Importing CT image data ..............................40
II. Importing MRI image data ............................40
Fusion visualization ..........................................40
Retrieval of previously loaded data ...................41
Positioning of landmarks for patient
registration ........................................................41
General information regarding
the positioning of landmarks ...........................41
Adding and moving landmarks on
the 3D surface model ......................................43
Adding and moving landmarks in
the 2D CT sectional views ..............................44
Adapting the visualization of patient data ..........45
Selecting the content of the window ...............45
Enlarging, reducing and moving
the slice views ................................................46
Softening the slice view ..................................47
..................25
....25
....................................26
...........................................26
.....28
.................................28
..........................................28
.............32
........................................32
..........................32
........................................33
...........................................34
.............................34
..............................34
.............35
........35
.............................................36
...............38
..............................................39
.39
............................40
........................40
............40
................41
...............................41
..................................41
... 43
...................44
...................45
...............................45
...............................46
..........................47