Reflex Reflexomat Silent Compact RSC 200 Betriebsanleitung Seite 37

10.4.3 Inspection intervals
Recommended maximum inspection intervals for operation in Germany pursuant
to Section 16 of the Industrial Safety Directive [Betriebssicherheitsverordnung] and
the classification of the device vessels in diagram 2 of the Directive 2014/68/EC,
applicable in strict compliance with the Reflex Installation, Operation and
Maintenance Manual.
For international use, observe the relevant national standards and regulations.
External inspection:
No requirement according to Annex 2, para. 4, 5.8.
Internal inspection:
Maximum interval according to Annex 2, para. 4, 5 and 6; if necessary, suitable
replacement actions are to be taken (such as wall thickness measurement and
comparison with the design specification which may be requested from the
manufacturer).
Strength test:
Maximum interval according to Annex 2, para. 4, 5 and 6.
Furthermore, compliance with Section 16 of the Industrial Safety Directive and
here in particular Section 16 (1) in connection with Section 15 and in particular
Annex 2, para. 4, 6.6 and Annex 2, para. 4, 5.8, must be ensured.
The actual intervals must be specified by the operating company based on a safety
evaluation taking into consideration the actual operating conditions, experience
with the mode of operation and charging material and the applicable national
regulations for the operation of pressure equipment.
11 Disassembly
DANGER
Risk of serious injury or death due to electric shock.
If live parts are touched, there is risk of life-threatening injuries.
•
Ensure that the supply cable to the device is disconnected and secured
against being switched back on.
•
Ensure that the system is secured and cannot be reactivated by other
persons.
•
Ensure that installation work for the electric connection of the device is
carried out by an electrician, and in compliance with electrical locally
applicable electrical engineering regulations.
CAUTION
Risk of burns on hot surfaces
Hot surfaces in heating systems can cause burns to the skin.
•
Wait until hot surfaces have cooled down or wear protective safety
gloves.
•
The operating authority is required to place appropriate warning signs in
the vicinity of the device.
CAUTION
Risk of injury due to pressurised liquid
If installation or maintenance work is not carried out correctly, there is a risk of
burns and other injuries at the connection points, if pressurised hot water or
steam suddenly escapes.
•
•
•
•
Prior to disassembly, block off all "water"-side connections to the device.
•
De-pressurise the device by venting it.
1. Disconnect the system from the power supply and secure it against
unintended reactivation.
2. Disconnect the power plug of the device from the voltage supply.
3. Open the draining ports at the vessel until water and compressed air are
completely removed.
4. Undo all hose and pipe connections from the vessel and the control unit of
the device to the system and remove them completely.

12
12.1
Central customer service
Central telephone number: +49 (0)2382 7069 - 0
Customer Service extension: +49 (0)2382 7069 - 9505
E-mail: aftersales@reflex.de
Technical Hotline
For questions about our products
Telephone number: +49 (0)2382 7069-9546
Monday to Friday 8:00 to 16:30
12.2
Device conformity declarations are available on the Reflex homepage.
www.reflex-winkelmann.com/konformitaetserklaerungen
Alternatively, scan the QR code:
12.3
The respective statutory guarantee regulations apply.
inhalt_en
Reflexomat Silent Compact — 06.12.2023
Ensure proper disassembly.
Wear suitable personal protective equipment (safety gloves and safety
goggles, for example).
Ensure that the system is de-pressurised before performing the
disassembly.
Note!
When using environmentally harmful media, an adequate liquid capture
facility must be provided when draining. Moreover, the operator is obliged
to ensure correct disposal of any such media.
Annex
Reflex Customer Service
Conformity and standards
Guarantee
Disassembly
English — 37