Siemens SINUMERIK 840D sl Funktionshandbuch Seite 909

Inhaltsverzeichnis
1 Kurzbeschreibung................................................................................................................................... 1-1
2 Ausführliche Beschreibung ..................................................................................................................... 2-1
2.1 3- bis 5-Achs-Transformation (F2) ............................................................................................. 2-1
2.1.1 Signale von Kanal (DB21, ...)..................................................................................................... 2-1
2.2 Gantry-Achsen (G1)................................................................................................................... 2-3
2.2.1 Signale an Achse/Spindel (DB31, ...) ........................................................................................ 2-3
2.2.2 Signale von Achse/Spindel (DB31, ...)....................................................................................... 2-4
2.3 Taktzeiten (G3) .......................................................................................................................... 2-7
2.4 Konturtunnel-Überwachung (K6) ............................................................................................... 2-7
2.5 Achskopplungen und ESR (M3)................................................................................................. 2-8
2.5.1 Signale an Achse (DB31, ...)...................................................................................................... 2-8
2.5.2 Signale von Achse (DB31, ...).................................................................................................... 2-8
2.6 Sollwertumschaltung (S9) ........................................................................................................ 2-10
2.6.1 Signale an Achse/Spindel (DB31, ...) ...................................................................................... 2-10
2.6.2 Signale von Achse/Spindel (DB31, ...)..................................................................................... 2-10
2.7 Tangentialsteuerung (T3)......................................................................................................... 2-11
2.7.1 Besondere Reaktion auf Signale ............................................................................................. 2-11
2.8 Installation von Compile-Zyklen (TE01)................................................................................... 2-11
2.9 Simulation von Compile-Zyklen (TE02) ................................................................................... 2-11
2.10 Abstandsregelung (TE1) .......................................................................................................... 2-11
2.10.1 Signale an Kanal (DB21, ...) .................................................................................................... 2-11
2.10.2 Signale von Kanal (DB21, ...)................................................................................................... 2-12
2.11 Analoge Achse (TE2)............................................................................................................... 2-14
2.12 Drehzahl-/Drehmomentkopplung, Master-Slave (TE3)............................................................ 2-14
2.12.1 Signale an Achse/Spindel (DB31, ...) ...................................................................................... 2-14
2.12.2 Signale von Achse/Spindel (DB31, ...)..................................................................................... 2-15
2.13 Transformationspaket Handling (TE4)..................................................................................... 2-16
2.13.1 Signale von Kanal (DB21, ...)................................................................................................... 2-16
2.14 MKS-Kopplung (TE6)............................................................................................................... 2-17
2.14.1 Signale an Achse/Spindel (DB31, ...) ...................................................................................... 2-17
2.14.2 Signale von Achse/Spindel (DB31, ...)..................................................................................... 2-18
2.15 Wiederaufetzen - Retrace Support (TE7) ................................................................................ 2-19
2.15.1 Signale an Kanal...................................................................................................................... 2-19
2.15.2 Signale von Kanal .................................................................................................................... 2-20
2.16 Taktunabhängige bahnsynchrone Schaltsignalausgabe (TE8) ............................................... 2-20
2.17 Achspaar Kollisionsschutz (TE9) ............................................................................................. 2-20
2.18 Vorverarbeitung (V2)................................................................................................................ 2-20
Sonderfunktionen: NC/PLC-Nahtstellensignale (Z3)
Funktionshandbuch, 11/2006, 6FC5397-2BP10-2AA0
iii