R R e e c c o o m m m m e e n n d d e e d d s s e e p p a a r r a a t t i i o o n n s s d d i i s s t t a a n n c c e e s s b b e e t t w w e e e e n n p p o o r r t t a a b b l l e e a a n n d d m m o o b b i i l l e e R R F F c c o o m m m m u u n n i i c c a a t t i i o o n n s s e e q q u u i i p p m m e e n n t t a a n n d d P P o o w w e e r r - -

P P o o w w e e r r - - L L O O A A D D is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.

The customer or the user of P P o o w w e e r r - - L L O O A A D D can help prevent electromagnetic interferences by maintaining a minimum

distance between portable and mobile RF communications equipment (transmitters) and P P o o w w e e r r - - L L O O A A D D as

recommended below, according to the maximum output power of the communications equipment.

R R a a t t e e d d m m a a x x i i m m u u m m o o u u t t p p u u t t

p p o o w w e e r r o o f f t t r r a a n n s s m m i i t t t t e e r r

W W

0.01

0.1

100

For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters

(m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output

power rating of the transmitter in watts (W) according to the transmitter manufacturer. Note 1: At 80 MHz and 800 MHz,

the separation distance for the higher frequency range applies. Note 2: These guidelines may not apply in all situations.

Electromagnetic propagation is affected by absorption and reflection from structures, objects, and people.

P P o o w w e e r r - - L L O O A A D D is suitable for use in the electromagnetic environment specified below. The customer or the user of

P P o o w w e e r r - - L L O O A A D D should assure that it is used in such an environment.

I I m m m m u u n n i i t t y y t t e e s s t t

Electrostatic discharge

(ESD)

IEC 61000-4-2

Surge

IEC 61000-4-5

Power frequency (50/60 Hz)

magnetic field

IEC 61000-4-8

Electrical transient

conduction along supply

ISO 7637-2

6390-809-005 Rev AA.0

S S e e p p a a r r a a t t i i o o n n d d i i s s t t a a n n c c e e a a c c c c o o r r d d i i n n g g t t o o f f r r e e q q u u e e n n c c y y o o f f t t r r a a n n s s m m i i t t t t e e r r

1 1 5 5 0 0 k k H H z z t t o o 8 8 0 0 M M H H z z

d d = = ( ( 1 1 . . 2 2 ) ) ( ( √ √ P P ) )

0.12

0.38

1.20

3.79

G G u u i i d d a a n n c c e e a a n n d d m m a a n n u u f f a a c c t t u u r r e e r r ' ' s s d d e e c c l l a a r r a a t t i i o o n n - - e e l l e e c c t t r r o o m m a a g g n n e e t t i i c c i i m m m m u u n n i i t t y y

E E N N / / I I E E C C 6 6 0 0 6 6 0 0 1 1 t t e e s s t t l l e e v v e e l l

+8 kV contact

+15 kV air

+1 kV line(s) to line(s)

+2 kV line(s) to ground

30 A/m

per ISO 7637-2

L L O O A A D D

m m

8 8 0 0 M M H H z z t t o o 8 8 0 0 0 0 M M H H z z

d d = = ( ( 0 0 . . 3 3 5 5 ) ) ( ( √ √ P P ) )

0.04