Siemens SINUMERIK 840D sl Funktionshandbuch Seite 17

8.17 Datenlisten .................................................................................................................................640
8.17.1 Maschinendaten.........................................................................................................................640
8.17.1.1 Allgemeine Maschinendaten......................................................................................................640
8.17.1.2 Kanal-spezifische Maschinendaten ...........................................................................................641
8.17.1.3 Achs-/Spindel-spezifische Maschinendaten ..............................................................................645
8.17.2 Settingdaten ...............................................................................................................................645
8.17.2.1 Kanal-spezifische Settingdaten..................................................................................................645
8.17.3 Signale .......................................................................................................................................645
8.17.3.1 Signale an NC ............................................................................................................................645
8.17.3.2 Signale an BAG .........................................................................................................................645
8.17.3.3 Signale von BAG........................................................................................................................646
8.17.3.4 Signale an Kanal........................................................................................................................646
8.17.3.5 Signale von KanaI......................................................................................................................647
8.17.3.6 Signale an Achse/Spindel ..........................................................................................................648
8.17.3.7 Signale von Achse/Spindel ........................................................................................................648
9 K2: Achsen, Koordinatensysteme, Frames............................................................................................ 649
9.1 Kurzbeschreibung ......................................................................................................................649
9.1.1 Achsen .......................................................................................................................................649
9.1.2 Koordinatensysteme ..................................................................................................................651
9.1.3 Frames .......................................................................................................................................653
9.2 Achsen .......................................................................................................................................657
9.2.1 Übersicht ....................................................................................................................................657
9.2.2 Maschinenachsen ......................................................................................................................658
9.2.3 Kanalachsen ..............................................................................................................................659
9.2.4 Geometrieachsen.......................................................................................................................659
9.2.5 Umschaltbare Geometrieachsen ...............................................................................................659
9.2.6 Zusatzachsen.............................................................................................................................664
9.2.7 Bahnachsen ...............................................................................................................................665
9.2.8 Positionierachsen.......................................................................................................................665
9.2.9 Hauptlaufachsen ........................................................................................................................666
9.2.10 Synchronachsen ........................................................................................................................667
9.2.11 Achskonfiguration ......................................................................................................................669
9.2.12 Link-Achsen ...............................................................................................................................671
9.3 Nullpunkte und Referenzpunkte.................................................................................................672
9.3.1 Bezugspunkte im Arbeitsraum ...................................................................................................672
9.3.2 Lage der Koordinatensysteme und Referenzpunkte .................................................................674
9.4 Koordinatensysteme ..................................................................................................................675
9.4.1 Übersicht ....................................................................................................................................675
9.4.2 Maschinenkoordinatensystem (MKS) ........................................................................................678
9.4.3 Basiskoordinatensystem (BKS) .................................................................................................680
9.4.4 Additive Korrekturen ..................................................................................................................682
9.4.5 Basis-Nullpunktsystem (BNS)....................................................................................................685
9.4.6 Einstellbares Nullpunktsystem (ENS) ........................................................................................687
9.4.7 Werkstückkoordinatensystem (WKS) ........................................................................................688
Frames .......................................................................................................................................688
9.5
9.5.1 Frame-Arten ...............................................................................................................................688
9.5.2 Frame-Komponenten .................................................................................................................690
9.5.2.1 Translation .................................................................................................................................690
9.5.2.2 Feinverschiebung.......................................................................................................................691
Grundfunktionen
Funktionshandbuch, 03/2013, 6FC5397-0BP40-3AA1
Inhaltsverzeichnis
17