MOTO GUZZI V10 CENTAURO Werkstatt-Handbuch Seite 37

N. CODE No. DESCRIPTION
1 01 92 91 00 Cap demounting wrench on cup and filter
2 14 92 96 00 Gear box support
3 19 92 96 00 Setting dial for distribution and ignition phase check
4 17 94 75 60 Arrow for distribution and ignition phase check
5 12 91 36 00 Tool for flywheel side flange disassembly
6 12 91 18 01 Tool for locking flywheel and crown starter
7 10 90 72 00 Tool for valve assembly and disassembly
8 30 91 28 10 Tool for internal clutch body locking
9 30 90 65 10 Tool for clutch assembly
10 12 90 59 00 Tool for clutch shaft disassembly with components
11 14 92 71 00 Instrument to install the sealing ring on the flange, flywheel side
12 12 91 20 00 Tool for flywheel side flange assembly complete with casing on engine shaft
13 14 92 72 00 Tool for distribution cover sealing ring assembly
14 12 90 71 00 Tool for transmission shaft locking
15 14 92 87 00 Tool for pre-selector activation
16 14 90 54 00 Tool for transmission shaft locking nut
17 14 91 26 03 Appropriate wrench for shaft internal clutch body retaining ring nut
18 14 91 31 00 Estractor for needle bearings on main shaft box and on clutch shaft cover
19 14 92 85 00 Tool for extracting the clutch shaft internal bearins track
20 17 94 92 60 Extractor for bearings for clutch shaft on box and transmission shaft on cover
21 17 94 50 60 Extractor for needle external bearings track for transmission shaft on box and
external bearings track on casing
22 14 90 70 00 Extractor for ball bearings for main shaft on cover
23 12 90 69 00 Extractor for transmission box needle bearings ring
24 17 94 83 60 Extractor for needle internal bearings track on box holed pin
25 17 94 84 60 Tool for pressing the internal needle bearings track on the transmission box holed
pin
26 17 94 88 60 Punch for the bearing external track of the drive shaft sealing ring
27 17 94 54 60 Tool for positioning the internal bearings ring on the main shaft and on the clutch
shaft
28 14 92 86 00 Tool for positioning the internal bearing ring on the transmission shaft
29 14 92 89 00 Punch for pressing the clutch shaft bearings on the box, for the transmission shaft
cover, and for the transmission box rear sealing ring
30 14 92 91 00 Punch for pressing the transmission shaft external needle bearings ring on the box
31 14 92 88 00 Punch for pressing the main shaft needle bearings on the box and the clutch shaft
on the cover
32 17 92 90 00 Punch for pressing the ball bearings for the main shaft on the cover
33 14 92 94 00 Punch for pressing the sealing ring on the clutch shaft gear box
34 14 92 95 00 Punch for pressing the sealing ring on the transmission shaft cover
35 17 94 51 60 Punch for pressing the external bearing tracks on the casing
36 14 92 93 00 Tool for positioning the sliding sleeve fork control
37 01 92 93 00 Locking ring nut wrench for front wheel pin
38 00 95 00 55 Manometer for engine oil pressure and fuel pressure check for vehicles with
electronic injection systems
39* 19 92 71 00 Tool for installing seal ring on flange, flywheel side
40* 14 92 73 00 Tool for holding camshaft gear
41* 65 92 84 00 Hub for degree whell
NOTE: The details with asterisk (*) apply to model SPORT 1100 I only.
35