Herunterladen Inhalt Inhalt Diese Seite drucken

Manitou EASY 2-Serie Bedienungsanleitung Seite 251

Inhaltsverzeichnis

Werbung

IT
E3 - Sostituire olio idraulico e trasmissi-
one
E3A - Pulizia/Sostituzione delle cartucce
di aspirazione impianto idraulico,
sostituzione dello sfiatatoio.
MRT-X 2145 - 2545
MRT 2145 - 2545
E3 - Sostituire olio idraulico e trasmissione
Mettere il carrello elevatore in piano, con il
motore termico spento e il braccio rientrato
e abbassato al massimo.
Prima di ogni intervento, pulire accura-
tamente intorno ai tappi di scarico e alla
succhieruola di aspirazione del serbatoio
idraulico.
Utilizzare un recipiente e un imbuto molto
pulito. Pulire inoltre la parte superiore del
bidone d'olio prima del riempimento.
Smaltire l'olio di scarico nel rispetto
dell'ambiente.
Scarico dell'olio
- Rimuovere il carter di protezione 1 (E3).
- Mettere un recipiente sotto il tappo di sca-
rico 2 (E3) e svitarlo.
- Togliere il tappo di riempimento 3 (E3) per
facilitare lo scarico.
E3A - Sostituzione dello sfiatatoio
- Svitare lo sfiatatoio 4 (E3) e sostituirlo con
uno nuovo (vedere:3 - MANUTENZIONE:
ELEMENTI FILTRANTI E CINGHIE).
E3A - Pulizia delle cartucce di aspirazione
impianto idraulico
1 - Cartuccia di aspirazione del serbatoio
dell'olio idraulico per pompa idrostatica
6.1 (E3).
2 - Cartuccia di aspirazione del serbatoio
dell'olio idraulico per pompa movimenti
6.2 (E3).
3 - Cartuccia di aspirazione del serbatoio
dell'olio idraulico (solo con predisposizi-
one cestello) 6.3 (E3).
- Scollegare il tubo 5 (E3).
3
4
5
E3 - Change the hydraulic and transmis-
sion oil
E3A - Cleaning/Replacing the hydraulic
system suction cartridges, replacing
the breather.
MRT-X 2145 - 2545
MRT 2145 - 2545
E3 - Change the hydraulic and transmission oil
Place the lift truck on level ground with the
engine stopped and telescope boom
retracted and lowered as far as possible.
Before any intervention, thoroughly clean
the area surrounding the drain plug and
the suction strainer on the hydraulic tank.
Use a clean container and funnel and clean
the underside of the oil drum before filling.
Dispose of the drain oil in an ecological
manner.
Draining the oil
- Remove the protective casing 1(E3).
- Place a container under drain plug 2 (E3)
and unscrew the plug.
- remove filling plug 3 to ensure that the oil
is drained properly.
E3A - Replacing the breather
- unscrew the breather 4 (E3) and replace
it with a new one (see: 3 - maintenance:
filters, cartridges and belts).
E3A - Cleaning/Replacing the hydraulic
system suction cartridges
1 -Suction cartridge of the hydraulic oil tank
to hydrostatic pump 6.1 (E3).
2 - Suction cartridge of the hydraulic oil tank
to movements pump 6.2 (E3).
3 - Suction cartridge for hydraulic oil tank
(only with basket predisposition) 6.3 (E3).
- Disconnect hose 5 (E3).
8
7
5
EN
E3 - Hydraulik- und Getriebeöl wechseln
E3A - Ansaugelemente der
MRT-X 2145 - 2545
MRT 2145 - 2545
E3 - Hydrauliköl und Getriebeöl wechseln
Teleskoplader auf eine waagerechte Fläche
fahren, Verbrennungsmotor abstellen und
Teleskopausleger maximal einfahren und
absenken.
Vor jedem Eingriff den Bereich um die
Auslassstopfen und den Ansaugstopfen am
Hydraulikbehälter gründlich reinigen.
Einen sehr sauberen Behälter und Trichter
benutzen. Außerdem den oberen Teil des
Ölbehälters vor dem Auffüllen reinigen.
Das Altöl unter Beachtung der Umwelt ent-
sorgen.
Öl ablassen
- Die Schutzabdeckung 1 (E3) abbauen.
-
Ablassschraube 2 (E3) stellen und Schraube
herausdrehen.
- Einfüllstopfen 3 (E3) entfernen, damit das
Öl korrekt ablaufen kann.
E3A - Austausch des Entlüftungsventils
- Das Entlüftungsventil 4 (E3) herausdre-
hen und gegen ein neues austauschen
(vgl.: 3 - WARTUNG: FILTERELEMENTE UND
KEILRIEMEN).
E3A - Reinigung der Ansaugfiltereinsätze
der Hydraulikanlage
1 - Saugfiltereinsatz des Hydraulikölbehälters
2 - Saugfiltereinsatz des Hydraulikölbehälters
3 - Saugfiltereinsatz des Hydraulikölbehälter
- Die Leitung 5 (E3) abtrennen.
2
6.1
6.3
3-55
DE
Hydraulikanlage reinigen/auswech-
seln, Entlüftungsventil auswechseln.
Einen
Auffangbehälter
unter
für hydrostatische Pumpe 6.1 (E3).
für Bewegungspumpe 6.2 (E3).
(nur bei Korbvorrüstung) 6.3 (E3).
1
6.2
die
E3

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Mrt 1440 easy 55p 400 st4 s2Mrt 1440 easy 75p 400 st3b s2Mrt-x 1440 easy 75p 400 st3a s2Mrt 1640 easy 55p 400 st4 s2Mrt 1640 easy 75p 400 st3b s2Mrt-x 1640 easy 75p 400 st3a s2 ... Alle anzeigen

Inhaltsverzeichnis