Scanlab RTC 5 Installation Und Inbetriebnahme Seite 248

Ausführen und Beenden von Listen mit
externen Steuersignalen und
Master/Slave-Synchronisation
(n_) set_control_mode_list
(n_) set_extstartpos_list
Listen-Handling und Strukturierte Program-
mierung
nor
(n_) list_continue ...................................... 352
uk
(n_) list_jump_pos ..................................... 354
uk
(n_) list_jump_rel ....................................... 356
nor
(n_) list_nop .............................................. 357
uk
(n_) list_repeat ........................................... 358
uk
(n_) list_until .............................................. 360
nor
(n_) long_delay ......................................... 385
nor
(n_) set_end_of_list
uk
(n_) set_list_jump ...................................... 501
nor
(n_) set_wait ............................................. 558
Unterprogramm-Befehle
uk
(n_) list_call
................................................ 349
uk
(n_) list_call_abs ........................................ 350
uk
(n_) list_return ........................................... 359
uk
(n_) sub_call ............................................... 584
uk
(n_) sub_call_abs ....................................... 585
(n_) sub_call_abs_repeat
uk
(n_) sub_call_repeat
Festlegen der Laserparameter
(n_) config_laser_signals_list
(n_) set_auto_laser_params_list
(n_) set_encoder_speed
(n_) set_firstpulse_killer_list
uk
(n_) set_laser_delays
(n_) set_laser_pin_out_list
vk
(n_) set_laser_pulses
vk
(n_) set_laser_timing
(n_) set_pulse_picking_list
(n_) set_qswitch_delay_list
(n_) set_softstart_level_list
(n_) set_softstart_mode_list
vk
(n_) set_standby_list
(n_) set_vector_control
® ®
RTC 5 PCI-Karte, RTC 5 PCI-Express-Karte, RTC
Rev. 1.10 d
10 Befehle und Funktionen
nor
...................... 461
uk
............................ 470
.................................. 469
uk
........................... 586
.................................. 587
vk
.................... 270
vk
................ 456
vk
............................. 467
uk
..................... 472
................................. 495
uk
........................ 497
.................................. 498
................................. 500
nor
....................... 526
uk
....................... 526
nor
...................... 540
var
.................... 542
.................................. 544
uk
............................. 555
®
5 PC/104-Plus-Karte, RTC
Festlegen der Scannerparameter
(n_) set_delay_mode_list
uk
(n_) set_jump_speed
vk
(n_) set_mark_speed
(n_) set_scanner_delays
(n_) set_sky_writing_limit_list
(n_) set_sky_writing_list
(n_) set_sky_writing_mode_list
(n_) set_sky_writing_para_list
Koordinatentransformationen
var
(n_) set_angle_list ..................................... 452
var (1)
(n_) set_defocus_list
var
(n_) set_matrix_list ................................... 504
var
(n_) set_offset_list .................................... 518
var (1)
(n_) set_offset_xyz_list
var
(n_) set_scale_list ...................................... 530
Online-Positionierung
nor
(n_) apply_mcbsp_list
(n_) set_mcbsp_matrix_list
(n_) set_mcbsp_rot_list
uk
(n_) set_mcbsp_x_list
uk
(n_) set_mcbsp_y_list
Direkte Laser- und Scan-Kopf-Steuerung
var
(n_) laser_on_list ....................................... 345
(n_) laser_on_pulses_list
(n_) laser_signal_off_list
(n_) laser_signal_on_list
(n_) para_laser_on_pulses_list
Das Scannen von Rasterbildern (Bitmaps)
(n_) set_default_pixel_list
var
(n_) set_n_pixel ......................................... 517
var
(n_) set_pixel ............................................. 521
nor
(n_) set_pixel_line ..................................... 522
mul (1)
(n_) set_pixel_line_3d
(1) nur bei freigeschalteter 3D-Option
nor normaler Listenbefehl
var variabler Listenbefehl
uk unverzögerter kurzer Listenbefehl
vk verzögerter kurzer Listenbefehl
mul multipler Listenbefehl
®
5 PCIe/104-Karte
mul
......................... 490
................................. 490
.................................. 502
vk
............................. 530
uk
.................. 533
nor
.......................... 533
nor
............... 535
nor
................. 538
............................ 463
........................ 520
.............................. 255
uk
....................... 509
uk
............................. 511
................................ 512
................................ 513
var
........................... 346
nor
.......................... 347
nor
........................... 348
var
................. 415
uk
......................... 461
.......................... 523
248