Scanlab RTC 5 Installation Und Inbetriebnahme Seite 245

®
iDRIVE -Befehle
(n_) control_command .................................. 273
(n_) get_transform ........................................ 320
(n_) read_user_data ....................................... 436
(n_) send_user_data ...................................... 450
transform ................................................ 612
(n_) upload_transform .................................. 615
Das Scannen von Rasterbildern (Bitmaps)
(n_) set_default_pixel .................................... 461
(1)
I/O-Befehle
(n_) get_free_variable ................................... 295
(n_) get_io_status .......................................... 301
(n_) get_mcbsp .............................................. 308
(n_) mcbsp_init .............................................. 403
(n_) mcbsp_init_spi ........................................ 404
(n_) periodic_toggle ...................................... 423
(2)
(n_) read_analog_in
(n_) read_io_port ........................................... 429
(n_) read_io_port_buffer ............................... 430
(n_) read_mcbsp ............................................ 432
(n_) read_multi_mcbsp .................................. 433
(n_) rs232_config ........................................... 439
(n_) rs232_read_data ..................................... 440
(n_) rs232_write_data ................................... 441
(n_) rs232_write_text .................................... 441
(n_) set_free_variable .................................... 483
(n_) set_laser_off_default ............................. 496
(n_) set_mcbsp_freq ...................................... 505
(n_) set_mcbsp_out_ptr ................................ 510
(n_) set_port_default ..................................... 524
(n_) write_8bit_port ...................................... 619
(n_) write_da_1 .............................................. 621
(n_) write_da_2 .............................................. 621
(n_) write_da_x .............................................. 622
(n_) write_io_port .......................................... 625
(n_) write_io_port_mask ............................... 625
Ausführen und Beenden von Listen mit
externen Steuersignalen und
Master/Slave-Synchronisation
(n_) get_counts .............................................. 291
(n_) get_master_slave ................................... 307
(n_) get_startstop_info .................................. 312
(n_) set_control_mode .................................. 459
(n_) set_extstartpos ....................................... 470
(n_) set_max_counts ...................................... 505
(n_) simulate_ext_start_ctrl ........................... 570
(n_) sync_slaves ............................................. 589
(1) siehe auch entsprechende Listenbefehle
®
(2) nur bei RTC 5 PCI-Express-Karte oder bei RTC
aufgesteckter ADC-Aufsteckplatine
® ®
RTC 5 PCI-Karte, RTC 5 PCI-Express-Karte, RTC
Rev. 1.10 d
10 Befehle und Funktionen
................................. 428
(1)
®
5 PCI-Karte mit
®
5 PC/104-Plus-Karte, RTC
Listen-Handling und -Status
(n_) auto_change ........................................... 263
(n_) auto_change_pos ................................... 264
(n_) get_status ............................................... 314
(n_) get_wait_status ...................................... 326
(n_) pause_list ................................................ 423
(n_) quit_loop ................................................ 425
(n_) read_status ............................................. 434
(n_) release_wait ............................................ 438
(n_) restart_list ............................................... 439
(n_) start_loop ............................................... 571
(n_) stop_execution ....................................... 582
(n_) stop_list .................................................. 582
Input-Pointer-Befehl
(n_) get_input_pointer .................................. 301
(n_) get_list_pointer ...................................... 303
(n_) load_list .................................................. 373
(n_) set_input_pointer ................................... 485
(n_) set_start_list ........................................... 544
(n_) set_start_list_1 ....................................... 544
(n_) set_start_list_2 ....................................... 544
(n_) set_start_list_pos .................................... 545
Output-Pointer-Befehl
(n_) execute_at_pointer ................................ 285
(n_) execute_list ............................................. 285
(n_) execute_list_1 ......................................... 285
(n_) execute_list_2 ......................................... 285
(n_) execute_list_pos ..................................... 286
(n_) get_out_pointer ..................................... 309
Unterprogramm-Befehle
(n_) copy_dst_src ........................................... 283
(n_) get_char_pointer .................................... 290
(n_) get_sub_pointer ..................................... 316
(n_) get_text_table_pointer .......................... 319
(n_) load_char ................................................ 362
(n_) load_sub ................................................. 381
(n_) load_text_table ....................................... 382
(n_) set_char_pointer ..................................... 457
(n_) set_char_table ........................................ 458
(n_) set_sub_pointer ...................................... 546
(n_) set_text_table_pointer ........................... 547
®
5 PCIe/104-Karte
(1)
(1)
245