Kontrollbefehle - Scanlab RTC 5 Installation Und Inbetriebnahme

10.1.5 Kontrollbefehle

Initialisierung der DLL
free_rtc5_dll ........................................... 289
get_rtc_mode ......................................... 309
init_rtc5_dll ............................................. 339
set_rtc4_mode ........................................ 528
set_rtc5_mode ........................................ 528
Verwendung mehrerer RTC
einem Rechner
acquire_rtc .............................................. 251
release_rtc .............................................. 437
rtc5_count_cards .................................... 443
select_rtc ................................................. 449
Listenspeicher-Befehle
(n_) config_list ............................................... 271
(n_) get_config_list ........................................ 291
(n_) get_list_space ......................................... 304
(n_) load_disk ................................................. 367
(n_) save_disk ................................................. 444
Initialisierung der Karte und Feldkorrektur
(1)
(n_) get_head_para ................................... 297
(1)
(n_) get_sync_status
(1)
(n_) get_table_para ................................... 318
(n_) load_correction_file
(n_) load_program_file
(n_) load_stretch_table
(2)
(n_) load_z_table ...................................... 384
read_abc_from_file ................................ 427
(1)
(n_) select_cor_table
(1)
(n_) set_dsp_mode .................................... 465
(1)
(n_) sync_slaves ......................................... 589
write_abc_to_file .................................... 620
(1) siehe auch entsprechende Listenbefehle
(2) nur bei freigeschalteter 3D-Option
® ®
RTC 5 PCI-Karte, RTC 5 PCI-Express-Karte, RTC
Rev. 1.10 d
10 Befehle und Funktionen
®
5-Karten in
................................. 317
(1)
........................... 363
(1)
............................. 377
(2)
............................ 380
................................. 446
®
5 PC/104-Plus-Karte, RTC
Laser-Version und Laser-Parameter
(n_) config_laser_signals ............................... 270
(n_) get_standby ............................................ 311
(n_) load_auto_laser_control ........................ 361
(n_) load_position_control ............................ 375
(n_) set_auto_laser_control ........................... 453
(n_) set_auto_laser_params .......................... 455
(n_) set_encoder_speed_ctrl ......................... 468
(n_) set_firstpulse_killer ................................ 472
(n_) set_laser_control .................................... 492
(n_) set_laser_mode ....................................... 496
(n_) set_laser_pulses_ctrl .............................. 499
(n_) set_pulse_picking ................................... 525
(n_) set_pulse_picking_length ...................... 525
(n_) set_qswitch_delay .................................. 526
(n_) set_softstart_level .................................. 539
(n_) set_softstart_mode ................................ 541
(n_) set_standby ............................................ 543
Festlegen der Scannerparameter
(n_) load_varpolydelay .................................. 383
(n_) set_delay_mode ..................................... 464
(n_) set_jump_speed_ctrl .............................. 490
(n_) set_mark_speed_ctrl .............................. 502
(n_) set_sky_writing ....................................... 532
(n_) set_sky_writing_limit ............................. 533
(n_) set_sky_writing_mode ........................... 534
(n_) set_sky_writing_para ............................. 536
Koordinatentransformationen
(n_) set_angle ................................................ 451
(2)
(n_) set_defocus ....................................... 462
(n_) set_matrix ............................................... 503
(n_) set_offset ................................................ 518
(2)
(n_) set_offset_xyz ................................... 519
(n_) set_scale .................................................. 529
Online-Positionierung
(n_) apply_mcbsp .......................................... 254
(n_) set_mcbsp_matrix .................................. 508
(n_) set_mcbsp_rot ........................................ 511
(n_) set_mcbsp_x ........................................... 512
(n_) set_mcbsp_y ........................................... 513
Statusüberwachung und Diagnose
(n_) get_head_status ..................................... 298
(n_) get_overrun ............................................ 309
(n_) get_value ................................................ 323
(n_) get_values ............................................... 325
(n_) get_waveform ........................................ 327
(n_) measurement_status .............................. 405
(n_) stop_trigger ............................................ 583
®
5 PCIe/104-Karte
(1)
(1)
(1)
(1)
(1)
244