Inhaltsverzeichnis
Werbung
Direkte Laser- und Scan-Kopf-Steuerung
(n_)
disable_laser ........................................... 284
(n_)
enable_laser ............................................ 284
(n_)
get_laser_pin_in ..................................... 302
(2)
(n_)
get_z_distance
(n_)
goto_xy ................................................... 329
(2)
(n_)
goto_xyz
............................................. 330
(n_)
laser_signal_off ...................................... 347
(n_)
laser_signal_on ....................................... 348
(n_)
set_laser_pin_out ................................... 497
Versionsbefehle
get_dll_version ....................................... 291
(n_)
get_hex_version ..................................... 299
(n_)
get_rtc_version ....................................... 310
(n_)
get_serial_number ................................. 311
Error-Befehle
(n_)
get_error ................................................. 293
(n_)
get_last_error ......................................... 303
(n_)
reset_error .............................................. 438
(n_)
set_verify ................................................ 557
verify_checksum ..................................... 616
Datum, Uhrzeit, Seriennummern
(n_)
get_list_serial .......................................... 304
(n_)
get_serial ................................................ 310
(n_)
select_serial_set ...................................... 450
(n_)
set_serial ................................................. 531
(n_)
set_serial_step ........................................ 531
(n_)
time_update ........................................... 592
"Processing on the fly"-Befehle
(n_)
get_encoder ............................................ 292
(n_)
get_fly_2d_offset ................................... 295
(n_)
get_marking_info ................................... 305
(n_)
init_fly_2d ............................................... 338
(n_)
load_fly_2d_table ................................... 369
(n_)
read_encoder .......................................... 429
(n_)
set_ext_start_delay ................................ 471
(3)
(n_)
set_mcbsp_in
..................................... 506
(n_)
set_multi_mcbsp_in
(n_)
set_rot_center ........................................ 527
(n_)
simulate_encoder ................................... 568
(n_)
simulate_ext_stop .................................. 570
(1) siehe auch entsprechende Listenbefehle
(2) nur bei freigeschalteter 3D-Option
(3) ohne "Processing on the fly"-Option nur eingeschränkte Funkti-
onalität
®
®
RTC
5 PCI-Karte, RTC
5 PCI-Express-Karte, RTC
Rev. 1.10 d
10 Befehle und Funktionen
(1)
.................................. 328
(1)
(1)
(3)
......................... 514
®
5 PC/104-Plus-Karte, RTC
Schrittmotoransteuerung
(n_)
get_stepper_status ................................. 315
(n_)
stepper_abs ............................................ 572
(n_)
stepper_abs_no ...................................... 573
(n_)
stepper_control ...................................... 574
(n_)
stepper_enable ....................................... 575
(n_)
stepper_init ............................................ 577
(n_)
stepper_rel .............................................. 579
(n_)
stepper_rel_no ........................................ 580
(1)
Sprungmodus
(n_)
get_jump_table ...................................... 302
(n_)
load_jump_table .................................... 370
(n_)
load_jump_table_offset ......................... 371
(n_)
set_jump_mode ...................................... 486
(n_)
set_jump_table ....................................... 491
Sonstige Kontrollbefehle
(n_)
auto_cal .................................................. 260
(n_)
bounce_supp .......................................... 265
(n_)
get_auto_cal ........................................... 290
(n_)
get_galvo_controls ................................. 296
(n_)
get_hi_data ............................................. 300
(n_)
get_hi_pos .............................................. 300
(n_)
get_time .................................................. 319
(n_)
home_position ....................................... 331
(n_)
home_position_xyz ................................ 332
(n_)
move_to .................................................. 410
(n_)
set_hi ....................................................... 484
(n_)
write_hi_pos ........................................... 624
®
5 PCIe/104-Karte
(1)
246
Werbung
Inhaltsverzeichnis
