Siemens SINUMERIK 828D Bedienhandbuch Seite 12

Inhaltsverzeichnis
11.2.11 Beliebige Positionen (CYCLE802) ...................................................................................... 400
11.2.12 Positionsmuster Reihe (HOLES1) ...................................................................................... 404
11.2.13 Positionsmuster Gitter oder Rahmen (CYCLE801) ............................................................. 406
11.2.14 Positionsmuster Kreis oder Teilkreis (HOLES2)................................................................... 410
11.2.15 Positionen ein- und ausblenden ....................................................................................... 416
11.2.16 Positionen wiederholen ................................................................................................... 418
11.3 Drehen ............................................................................................................................ 419
11.3.1 Allgemeines..................................................................................................................... 419
11.3.2 Abspanen (CYCLE951) ..................................................................................................... 419
11.3.3 Einstich (CYCLE930)......................................................................................................... 422
11.3.3.1 Funktion .......................................................................................................................... 422
11.3.3.2 Parameter........................................................................................................................ 425
11.3.4 Freistich Form E und F (CYCLE940) ................................................................................... 426
11.3.5 Gewindefreistiche (CYCLE940) ......................................................................................... 428
11.3.6 Gewindedrehen (CYCLE99) .............................................................................................. 431
11.3.6.1 Besonderheiten der Auswahlalternativen zu Zustelltiefen ................................................. 448
11.3.7 Gewindekette (CYCLE98).................................................................................................. 449
11.3.7.1 Besonderheiten der Auswahlalternativen zu Zustelltiefen ................................................. 455
11.3.8 Abstich (CYCLE92) ........................................................................................................... 456
11.4 Konturdrehen .................................................................................................................. 458
11.4.1 Allgemeines..................................................................................................................... 458
11.4.2 Darstellung der Kontur ..................................................................................................... 459
11.4.3 Neue Kontur anlegen ....................................................................................................... 460
11.4.4 Konturelemente erstellen................................................................................................. 462
11.4.5 Passungsmaß eingeben.................................................................................................... 468
11.4.6 Kontur ändern ................................................................................................................. 469
11.4.7 Konturaufruf (CYCLE62) - nur bei G-Code-Programm ........................................................ 470
11.4.8 Abspanen (CYCLE952) ..................................................................................................... 471
11.4.9 Abspanen Rest (CYCLE952) .............................................................................................. 482
11.4.10 Stechen (CYCLE952) ........................................................................................................ 484
11.4.11 Stechen Rest (CYCLE952) ................................................................................................. 490
11.4.12 Stechdrehen (CYCLE952).................................................................................................. 492
11.4.13 Stechdrehen Rest (CYCLE952) .......................................................................................... 498
11.5 Fräsen ............................................................................................................................. 501
11.5.1 Planfräsen (CYCLE61)....................................................................................................... 501
11.5.2 Rechtecktasche (POCKET3)............................................................................................... 504
11.5.3 Kreistasche (POCKET4)..................................................................................................... 514
11.5.4 Rechteckzapfen (CYCLE76) ............................................................................................... 523
11.5.5 Kreiszapfen (CYCLE77) ..................................................................................................... 530
11.5.6 Mehrkant (CYCLE79) ........................................................................................................ 537
11.5.7 Längsnut (SLOT1) ............................................................................................................ 542
11.5.8 Kreisnut (SLOT2) .............................................................................................................. 551
11.5.9 Offene Nut (CYCLE899) .................................................................................................... 559
11.5.10 Langloch (LONGHOLE) - nur bei G-Code-Programm........................................................... 571
11.5.11 Gewindefräsen (CYCLE70)................................................................................................ 573
11.5.12 Gravur (CYCLE60) ............................................................................................................ 577
11.6 Konturfräsen ................................................................................................................... 585
11.6.1 Allgemeines..................................................................................................................... 585
11.6.2 Darstellung der Kontur ..................................................................................................... 585
11.6.3 Neue Kontur anlegen ....................................................................................................... 586
12
Bedienhandbuch, 07/2021, 6FC5398-8CP41-0AA1
Drehen