Herunterladen Diese Seite drucken

Bosch Performance Line SX Drive Unit Originalbetriebsanleitung Seite 272

Vorschau ausblenden Andere Handbücher für Performance Line SX Drive Unit:

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 368
eBike battery from being removed by unauthorised third
parties when the eBike is not in use.
CompactTube battery (built-in)
The eBike batteries built-in to the bicycle frame must only be
removed in the event of a fault. Contact an authorised bi-
cycle dealer if this happens.
Removing the CompactTube battery (pivot)
(see figure F)
❶ To remove the CompactTube battery (20), open the
battery lock (2) with the key (1) or press on the un-
locking element (24) with a suitable, non-pointed tool
(e.g. a hex key). The battery will be unlocked and fall
into the safety restraint (22).
Note: When removing the eBike battery, hold it firmly in your
hand.
❷ Hold the battery firmly, gently slide the battery to-
wards the battery lock (2) and remove it from the
safety restraint (22).
Note: The unlocking element may vary from the image and
may be a manufacturer-specific solution. Read the operating
instructions of the eBike manufacturer.
Note: As a result of varying designs, the battery may need
to be inserted and removed using a different method. Read
the operating instructions of the eBike manufacturer.
Inserting the CompactTube battery (pivot) (see figure G)
❶ To insert the CompactTube battery (20), place it so
that its contacts are in the upper holder of the frame.
❷ Swivel the battery into the bicycle frame until it is held
by the safety restraint (22).
❸ Push the battery into the guide rail (11) and slide the
battery into the battery lock (2) until you hear it click
into place.
❹ Then remove the key (1) from the battery lock (2).
Always remove the key (1) from the battery lock (2) after
locking it. This prevents both the key from falling out and the
eBike battery from being removed by unauthorised third
parties when the eBike is not in use.
Removing the CompactTube battery (axial)
(see figure H)
❶ To remove the CompactTube battery (21), open the
battery lock (2) with the key (1) or press on the un-
locking element (24) with a suitable, non-pointed tool
(e.g. a hex key). The battery will be unlocked and fall
into the safety restraint (23).
Note: When removing the eBike battery, hold it firmly in your
hand.
❷ Press the safety restraint (23). Hold the battery firmly
in place if the battery is sliding out of the bicycle
frame. Then remove the battery.
Note: The unlocking element may vary from the image and
may be a manufacturer-specific solution. Read the operating
instructions of the eBike manufacturer.
Bosch eBike Systems
Note: As a result of varying designs, the battery may need
to be inserted and removed using a different method. Read
the operating instructions of the eBike manufacturer.
Inserting the CompactTube battery (axial) (see figure I)
❶ To insert the CompactTube battery (21), insert it into
the frame with the socket for the charging con-
nector (5) facing upwards until you hear the battery
click into place in the safety restraint (23). Ensure that
the battery is aligned correctly.
❷ Slide the battery into the battery lock (2) until you
hear it click into place in the battery lock (2).
❸ Then remove the key (1) from the battery lock (2).
Always remove the key (1) from the battery lock (2) after
locking it. This prevents both the key from falling out and the
eBike battery from being removed by unauthorised third
parties when the eBike is not in use.
Inserting and Removing the PowerPack Battery
(see figure J)
In order to insert the battery, the key (1) must not be inser-
ted in the battery lock (2).
❶ To insert the PowerPack battery (15), place it so that
its contacts are in the lower holder (16) on the eBike.
❷ Twist it into the upper holder (14) as far as possible
until you hear it click into place.
Always remove the key (1) from the battery lock (2) after
locking it. This prevents both the key from falling out and the
eBike battery from being removed by unauthorised third
parties when the eBike is not in use.
❶ To remove the PowerPack battery (15), switch it off
and open the battery lock (2) using the key (1).
❷ Twist the battery out of the upper holder (14) and pull
it out of the lower holder (16).
Inserting and removing the rack-mounted battery
(see figure K)
In order for the battery to be inserted, the battery lock (2)
must be locked. The key (1) must not be inserted in the bat-
tery lock (2).
To insert the battery (27), slide its contacts into the
holder (26) until you hear it click into place.
To remove the battery (27), switch it off and open the bat-
tery lock using the key (1) ❶.
Pull the battery out of the holder (26) ❷.
Operation
Start-up
Switching on/off
Switching on the eBike battery is one way to switch on the
eBike (does not apply to permanently installed eBike batter-
ies). To do this, read and follow the instructions in the oper-
ating manuals for the drive unit and operating unit.
Before switching on the eBike battery, i.e. the eBike, make
sure that the battery lock (2) is locked.
English – 5
0 275 007 3PX | (08.02.2024)

Werbung

loading

Diese Anleitung auch für:

Bdu3142Bdu3143Bdu3144Bdu3145