Bosch Performance Line SX Drive Unit Originalbetriebsanleitung Seite 915

English – 2
All illustrations of bike parts except for the drive unit, on-
board computer (including operating unit), speed sensor
and the corresponding holders are a schematic representa-
tion and may differ on your eBike.
(1) Ambient light sensor
(2) On/off button
(3) Charge indicator of the eBike battery
(4) ABS LED (optional)
(5) Riding mode LED
(6) Holder
(7) Select button
(8) Diagnostics connection (for servicing purposes
only)
(9) Button for decreasing the assistance level –/
walk assistance
(10) Button for increasing the assistance level +/
bicycle lights
(11) Button to reduce brightness/
go back
(12) Button to increase brightness/
go forward
Technical data
Operating unit
Product code
Max. charging current of USB
A)
port
A)
USB port charging voltage
B)
USB charging cable
Charging temperature
Operating temperature
Storage temperature
Diagnostic interface
Internal lithium-ion battery
Protection rating
Dimensions (without fastening)
Weight
Bluetooth® Low Energy 5.0
– Frequency
– Transmission power
A) Specification for charging the LED Remote operating unit; ex-
ternal devices cannot be charged.
B) Not included with the product as standard
C) USB Type-C® and USB-C® are trademarks of USB Implementers
Forum.
The licence information for the product can be accessed at the follow-
ing Internet address: www.bosch-ebike.com/licences
0 275 007 3RL | (25.02.2024)
Declaration of Conformity
Robert Bosch GmbH, Bosch eBike Systems, hereby declares
that the LED Remote radio communication unit complies
with Directive 2014/53/EU. The full text of the EU Declara-
tion of Conformity can be accessed at the following Internet
address: www.bosch-ebike.com/conformity.
Robert Bosch GmbH, Bosch eBike Systems, hereby declares
that the LED Remote radio communication unit complies
with the Radio Equipment Regulations 2017 (SI
2917/1206). The full text of the UK Declaration of Conform-
ity can be accessed at the following Internet address:
www.bosch-ebike.com/conformity.
Operation
Requirements
The eBike can then only be switched on when the following
requirements are met:
– A sufficiently charged eBike battery is inserted (see oper-
ating instructions for the eBike battery from the system
generation the smart system).
– The speed sensor is connected properly (see operating
instructions for the drive unit from the system genera-
LED Remote
tion the smart system).
Before riding off, ensure that the buttons on the operating
BRC3600
unit are within easy reach. We recommend that you align the
mA 600
unit so that the plus/minus button level is perpendicular to
the floor.
V 5
Note: All screenshots showing the display and text are from
C)
USB Type-C® the approved software version. The display, text and/or
functions may change following a software update.
°C 0 to +40
°C –5 to +40
Operating unit power supply
°C +10 to +40
If a sufficiently charged eBike battery is inserted into the
C)
USB Type-C®
eBike and the eBike is switched on, then the internal operat-
ing unit battery is powered and charged.
V 3.7
If the state of charge of the internal operating unit battery is
mAh 75
very low, you can charge it via the diagnostics connec-
IP55
tion (8) with a USB Type-C® cable using a power bank or an-
mm 74 × 53 × 35
other suitable power source (charging voltage 5 V; charging
g 30
current max. 600 mA).
Always close the flap of the diagnostics connection (8) so
that no dust or moisture can enter.
MHz 2400–2480
mW 1
Switching the eBike On and Off
To switch on the eBike, briefly press the on/off button (2).
After the starting animation, the state of charge of the eBike
battery is displayed in colour with the battery charge indic-
ator (3) and the set riding mode with the (5) display. The
eBike is ready to ride.
The display brightness is controlled by the ambient light
sensor (1). Therefore, do not cover the ambient light
sensor (1).
Bosch eBike Systems