Bosch Performance Line SX Drive Unit Originalbetriebsanleitung Seite 919

English – 6
mode LED (5) once again continuously shows the colour of
the set riding mode.
You can use the following table to rectify the errors yourself
if necessary. Otherwise, please contact your bicycle retailer.
Number Troubleshooting
523005 The indicated error numbers show that
there is interference when the sensors de-
514001
tect the magnetic field. See whether you
514002
have lost the magnet while riding.
514003
If you are using a magnet sensor, check that
514006
the sensor and magnet have been properly
installed. Make sure too that the cable to the
sensor is not damaged.
If you are using a rim magnet, make sure that
you do not have any magnetic field interfer-
ence in the vicinity of the drive unit.
680007 The indicated error numbers show that the
eBike battery is outside of the permissible
680009
operating temperature. The charging of the
680012
eBike battery is interrupted.
680014
As soon as the operating temperature re-
680016
turns to the permissible range, the charging
process will start again.
680017
Critical errors
Critical errors are shown by the riding mode LED (5) and the
battery charge indicator of the eBike battery (3) flashing red
and then lighting up continuously. Follow the instructions in
the table below if a critical error occurs.
Number Instructions
6A0004 Remove the PowerMore battery and restart
your eBike.
If the problem persists, please contact your
specialist dealer.
890000 – Acknowledge the error code.
– Restart the eBike system.
If the problem persists:
– Acknowledge the error code.
– Perform software update.
– Restart the eBike system.
If the problem persists:
– Please contact a Bosch eBike Systems
specialist dealer.
0 275 007 3RL | (25.02.2024)
Maintenance and servicing
Maintenance and cleaning
The operating unit must not be cleaned with pressurised wa-
ter.
Keep the operating unit clean. Dirt can cause faulty bright-
ness detection.
Clean your operating unit using a soft cloth dampened only
with water. Do not use cleaning products of any kind.
Have all repairs performed only by an authorised bike
u
dealer.
Note: If you are handing in your eBike to a bicycle dealer for
maintenance, it is recommended that you temporarily deac-
tivate <Lock & Alarm>.
Note: If you do not use the LED Remote operating unit for a
long time, charge it in accordance with (see "Operating unit
power supply", page English – 2).
After-sales service and advice on using products
If you have any questions about the eBike and its compon-
ents, contact an authorised bicycle dealer.
For contact details of authorised bike dealerships, please
visit www.bosch-ebike.com.
Further information on the eBike components
and their functions can be found in the Bosch
eBike Help Center.
Disposal and substances in products
You can find information about substances in products at the
following link:
www.bosch-ebike.com/en/material-compliance.
Do not dispose of eBikes and their components with house-
hold waste.
An in-store return is possible, provided the retailer voluntar-
ily offers a return or is legally obligated to do so. Refer to the
national regulations in this case.
The drive unit, on-board computer incl. operat-
ing unit, eBike battery, speed sensor, ac-
cessories and packaging should be disposed of
in an environmentally correct manner.
Check that your personal data has been deleted from the
device.
Batteries that can be removed from the power tool without
destruction must be removed before disposal itself and sor-
ted for separate battery collection.
In accordance with Directive 2012/19/EU
and Directive 2006/66/EC respectively, elec-
tronic devices that are no longer usable and de-
fective/drained batteries must be collected
separately and recycled in an environmentally
friendly manner.
Electrical and electronic equipment are collected separately
for pre-sorting by type and helps to ensure that raw materi-
Bosch eBike Systems