Siemens SINAMICS S120 Handbuch Seite 661

SERUPRO_SPEED_FACTOR
SERUPRO_SPEED_MODE
SERUPRO_SYNC_MASK
SERVO_DISABLE_DELAY_TIME
SETINT_ASSIGN_FASTIN
SHAPED_TOOL_CHECKSUM
SHAPED_TOOL_TYPE_NO
SIEM_TRACEFILES_CONFIG
Signale an Achse/Spindel
Signale an Kanal
Signale NCK
Signale von Achse/Spindel
Signale von Bedientafel
Signale von HMI
Signale von Kanal
Signale von/an HMI
SIMU_AX_VDI_OUTPUT
SINAMICS_ALARM_MASK
SINAMICS_IBN_TIMEOUT_VALUE
SINGLEBLOCK2_STOPRE
SLASH_MASK
SMOOTH_ORI_TOL
SOFT_ACCEL_FACTOR
SOFTKEY_CENTRE_ADJ
SPF_END_TO_VDI
SPIND_ACTIVE_AFTER_RESET
SPIND_ASSIGN_TO_MACHAX
SPIND_CONSTCUT_S
SPIND_DEF_MASTER_SPIND
SPIND_DEFAULT_ACT_MASK
Maschinendaten und Nahtstellensignale
Listenhandbuch, 03/2011, 6FC5397-5CP10-3AA0
MD 22601 , 280
MD 22600 , 279
,
MD 42125 487
MD 36620 , 453
MD 21210 , 262
MD 20372 , 237
MD 20370 , 236
MD 11294 , 118
,
, 580
, 573
, 567
,
566
, 596
, 564
MD 30350 , 368
MD 13150 , 152
MD 1091 , 30
MD 42200 , 490
MD 10706 , 82
MD 42466 , 493
MD 32433 , 394
MD 1106 , 32
MD 20800 , 254
MD 35040 , 430
MD 35000 , 425
MD 43202 , 511
MD 20090 , 208
MD 35030 , 428
SPIND_DEFAULT_MODE
MD 35020
SPIND_DES_VELO_TOL
MD 35150
SPIND_EXTERN_VELO_LIMIT
MD 35160
SPIND_FUNC_RESET_MODE
MD 35032
SPIND_FUNCTION_MASK
MD 35035
SPIND_MAX_VELO_G26
MD 43220
SPIND_MAX_VELO_LIMS
MD 43230
SPIND_MIN_VELO_G25
MD 43210
608 SPIND_ON_SPEED_AT_IPO_START
MD 35500
SPIND_OSCILL_ACCEL
, 624 MD 35410
SPIND_OSCILL_DES_VELO
MD 35400
SPIND_OSCILL_START_DIR
MD 35430
SPIND_OSCILL_TIME_CCW
MD 35450
SPIND_OSCILL_TIME_CW
MD 35440
SPIND_POSCTRL_VELO
MD 35300
SPIND_POSIT_DELAY_TIME
MD 35310
SPIND_POSITIONING_DIR
MD 35350
SPIND_RIGID_TAPPING_M_NR
MD 20094
SPIND_S
MD 43200
SPIND_SPEED_TYPE
MD 43206
SPIND_STOPPED_AT_IPO_START
MD 35510
SPIND_VELO_LIMIT
MD 35100
SPINDEL_LOAD_BAR_COL1
MD 366
SPINDEL_LOAD_BAR_MAX
MD 365
SPINDEL_LOAD_DISPLE1
MD 360
SPINDLE_DISP_MODE
MD 379
, 427
, 435
,
436
, 428
, 428
, 513
, 513
, 512
, 441
, 439
,
439
, 440
, 440
, 440
, 438
, 438
, 439
, 208
, 511
, 512
, 441
, 431
, 25
, 25
, 24
, 27
Index
661