Siemens SINAMICS S120 Handbuch Seite 310

Maschinendaten
2.3 Kanalspezifische NC-Maschinendaten
24771
-
-
802d-cu3
802d-ng2
802d-ng3
802d-tm1
802d-tm2
802d-tm3
Beschreibung: Gibt für jeden Kanal für die zweite TRAANG-Transformation die Achsbeschleuni-
gungsreserve für Jog-, Positionier- und Pendelbewegungen an, die auf der par-
allelen Achse (siehe MD2.... $MC_TRAFO_AXES_IN_...[1]) für die
Ausgleichsbewegung bereitgehalten wird.
Korrespondiert mit:
$MC_TRAANG_PARALLEL_RES_1
24800
Grad
-
802d-cu3
802d-ng2
802d-ng3
802d-tm1
802d-tm2
802d-tm3
Beschreibung: Gibt für die erste vereinbarte TRACYL-Transformation den Offset der Rundachse
in Grad gegenüber der Nullstellung während TRACYL aktiv an.
Korrespondiert mit:
MD24850 $MC_TRACYL_ROT_AX_OFFSET_2
310
TRAANG_PARALLEL_ACCEL_RES_2
Beschleunigungsreserve der Parallelachse für 2.
TRAANG-Trafo
- 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
- 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
- 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
- 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
- 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
- 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
TRACYL_ROT_AX_OFFSET_1
Offset der Rundachse für die 1. TRACYL-Transformation
- 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
- 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
- 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
- 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
- 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
- 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
C07
DOUBLE
0.0 1.0
0.0 1.0
0.0 1.0
0.0 1.0
0.0 1.0
0.0 1.0
C07
DOUBLE
- -
- -
- -
- -
- -
- -
Maschinendaten und Nahtstellensignale
Listenhandbuch, 03/2011, 6FC5397-5CP10-3AA0
M1
NEW CONF
2/2
2/2
2/2
-1/7
-1/7
-1/7
M1
NEW CONF
2/2
-1/7
-1/7
0/0
2/2
2/2