Siemens SINAMICS S120 Handbuch Seite 482

NC-Settingdaten
3.1 NC-Settingdaten
41520
s
-
802d-cu3
802d-ng2
802d-ng3
802d-tm1
802d-tm2
802d-tm3
Beschreibung: In das Settingdatum kann zur Kompensation von Verzögerungszeiten jedem Nocken
1-8 eine Vorhalte- bzw. Verzögerungszeit zugeordnet werden.
Die Schaltflanke des zugehörigen Nockensignals wird um die eingegebene Zeit
vorverlegt bzw. verzögert.
Positiver Wert:
Negativer Wert:
Der Index [n] des Settingdatums adressiert das Nockenpaar:
n = 0, 1, ... , 7 entspricht Nockenpaar 1, 2, ... , 8
Das Settingdatum wirkt additiv zu dem MD10460 $MN_SW_CAM_MINUS_LEAD_TIME[n].
korrespondierend mit ....
MD10460 $MN_SW_CAM_MINUS_LEAD_TIME[n] (Vorhalte- bzw. Verzögerungszeit an
den Minusnocken 1 - 16)
41521
s
-
802d-cu3
802d-ng2
802d-ng3
802d-tm1
802d-tm2
802d-tm3
In das Settingdatum kann zur Kompensation von Verzögerungszeiten jedem Plus-
Beschreibung:
nocken 1-8 eine Vorhalte- bzw. Verzögerungszeit zugeordnet werden.
Die Schaltflanke des zugehörigen Nockensignals wird um die eingegebene Zeit
vorverlegt bzw. verzögert.
Positiver Wert:
Negativer Wert:
482
SW_CAM_MINUS_TIME_TAB_1
Vorhaltezeit zu '-'-Schaltpunkten der Nocken 1-8
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
Vorhaltezeit
Verzögerungszeit
SW_CAM_PLUS_TIME_TAB_1
Vorhaltezeit zu '+'-Schaltpunkten der Nocken 1-8
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
Vorhaltezeit
Verzögerungszeit
-
DOUBLE
- -
- -
- -
- -
- -
- -
-
DOUBLE
- -
- -
- -
- -
- -
- -
Maschinendaten und Nahtstellensignale
Listenhandbuch, 03/2011, 6FC5397-5CP10-3AA0
N3
SOFORT
7/7
7/7
7/7
-1/7
-1/7
-1/7
N3
SOFORT
7/7
7/7
7/7
-1/7
-1/7
-1/7