Siemens SINAMICS S120 Handbuch Seite 481

41500
mm/inch, Grad
-
802d-cu3
802d-ng2
802d-ng3
802d-tm1
802d-tm2
802d-tm3
Beschreibung: In das Maschinendatum wird die Nockenposition der Minusnocken 1 - 8 eingetra-
gen.
Die Positionen werden im Maschinenkoordinatensystem eingetragen.
Der Index [n] des Settingdatums adressiert das Nockenpaar:
n = 0, 1, ... , 7 entspricht Nockenpaar 1, 2, ... , 8
Bei Überfahren der eingestellten Schaltpunkte in positiver Achsrichtung
schalten die zugehörigen "Minus"-Nockensignale in der PLC-Nahtstelle ( und
evtl. applizierte schnelle Ausgangssignale ) von 1 nach 0.
41501
mm/inch, Grad
-
802d-cu3
802d-ng2
802d-ng3
802d-tm1
802d-tm2
802d-tm3
Beschreibung: In das Maschinendatum wird die Nockenposition der Plusnocken 1 - 8 eingetra-
gen.
Die Positionen werden im Maschinenkoordinatensystem eingetragen.
Der Index [n] des Settingdatums adressiert das Nockenpaar:
n = 0, 1, ... , 7 entspricht Nockenpaar 1, 2, ... , 8
Bei Überfahren der eingestellten Schaltpunkte in positiver Achsrichtung
schalten die zugehörigen "Plus"-Nockensignale in der PLC-Nahtstelle ( und
evtl. applizierte schnelle Ausgangssignale ) von 0 nach 1.
Maschinendaten und Nahtstellensignale
Listenhandbuch, 03/2011, 6FC5397-5CP10-3AA0
SW_CAM_MINUS_POS_TAB_1
Schaltpunkte bei fallender Nocke 1-8
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
SW_CAM_PLUS_POS_TAB_1
Schaltpunkte bei steigender Nockenflanke 1-8
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0
-
DOUBLE
- -
- -
- -
- -
- -
- -
-
DOUBLE
- -
- -
- -
- -
- -
- -
NC-Settingdaten
3.1 NC-Settingdaten
N3
SOFORT
7/7
7/7
7/7
-1/7
-1/7
-1/7
N3
SOFORT
7/7
7/7
7/7
-1/7
-1/7
-1/7
481