Siemens SINAMICS S120 Handbuch Seite 62

Maschinendaten
2.2 Allgemeine NC-Maschinendaten
10460
s
-
802d-cu3
802d-ng2
802d-ng3
802d-tm1
802d-tm2
802d-tm3
Beschreibung: In diesem Maschinendatum kann zur Kompensation von Verzögerungszeiten jedem
Minusnocken 1-16 eine Vorhalte- bzw. Verzögerungszeit zugeordnet werden.
Die Schaltflanke des zugehörigen Nockensignals wird um die eingegebene Zeit
vorverlegt bzw. verzögert.
Positiver Wert:
Negativer Wert:
Dient zur Kompensation des konstanten Anteils der interner Verzögerungszeit
zwischen Istwerterfassung und Signalausgabe.
Der Index [n] des Maschinendatums adressiert das Nockenpaar:
n = 0, 1, ... , 15 entspricht Nockenpaar 1, 2, ... , 16
Das Maschinendatum wirkt additiv zu den SD41520
$SN_SW_CAM_MINUS_TIME_TAB_1[n]
Korrespondiert mit:
SD41520 $SN_SW_CAM_MINUS_TIME_TAB_1[n] (Vorhalte- bzw. Verzögerungszeit an
den Minusnocken 1 -8)
10461
s
-
802d-cu3
802d-ng2
802d-ng3
802d-tm1
802d-tm2
802d-tm3
In diesem Maschinendatum kann zur Kompensation von Verzögerungszeiten jedem
Beschreibung:
Plusnocken 1-16 eine Vorhalte- bzw. Verzögerungszeit zugeordnet werden.
62
SW_CAM_MINUS_LEAD_TIME
Vorhalte- bzw. Verzögerungszeit an den Minus-Nocken 1-
16
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
1 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
1 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
1 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
--> Vorhaltezeit
--> Verzögerungszeit
SW_CAM_PLUS_LEAD_TIME
Vorhalte- bzw. Verzögerungszeit an den Plus-Nocken 1-16 DOUBLE
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
8 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
1 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
1 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
1 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
N09
DOUBLE
- -
- -
- -
- -
- -
- -
N09
- -
- -
- -
- -
- -
- -
Maschinendaten und Nahtstellensignale
Listenhandbuch, 03/2011, 6FC5397-5CP10-3AA0
N3
POWER ON
3/3
3/3
3/3
0/0
0/0
0/0
N3
POWER ON
3/3
3/3
3/3
0/0
0/0
0/0