Siemens SINAMICS S120 Handbuch Seite 491
Maschinendaten und
nahtstellensignale
Vorschau ausblenden
Andere Handbücher für SINAMICS S120:
- Handbuch (2612 Seiten) ,
- Funktionshandbuch (1028 Seiten) ,
- Gerätehandbuch (846 Seiten)
Inhaltsverzeichnis
Werbung
42402
s
-
802d-cu3
802d-ng2
802d-ng3
802d-tm1
802d-tm2
802d-tm3
Beschreibung:
Die Wirkung dieses Settingdatums ist identisch mit der des MD26018
$MC_NIBBLE_PRE_START_TIME. Es dient in erster Linie dazu, die Vorauslösezeit
aus dem NC-Programm heraus zu verändern, um diese an unterschiedliche Blech-
größen und -dicken anpassen zu können. Das Settingdatum wird allerdings nur
dann wirksam, wenn das Maschinendatum Null gesetzt wurde.
korrespondierend mit .... NIBBLE_PRESTART_TIME
42404
s
-
802d-cu3
802d-ng2
802d-ng3
802d-tm1
802d-tm2
802d-tm3
Mindestzeit zwischen 2 Hüben in Sekunden
Beschreibung:
42440
-
-
-
Beschreibung:
0:
sel nur das programmierte Positionsdelta gefahren. Nullpunktverschiebungen
in FRAMES werden dann nur bei absoluter Positionsangabe herausgefahren.
1:
wechsel Änderungen von Nullpunktverschiebungen herausgefahren. (Standardver-
halten bis SW 3)
korrespondierend mit ....
SD42442 $SC_TOOL_OFFSET_INCR_PROG
Maschinendaten und Nahtstellensignale
Listenhandbuch, 03/2011, 6FC5397-5CP10-3AA0
NIBPUNCH_PRE_START_TIME
Verzögerungszeit (Stanzen/Nibbeln) mit G603
-
.02,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
-
.02,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
-
.02,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
-
.02,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
-
.02,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
-
.02,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
MINTIME_BETWEEN_STROKES
Mindestzeit zwischen 2 Hüben in Sekunden
-
0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
-
0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
-
0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
-
0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
-
0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
-
0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
FRAME_OFFSET_INCR_PROG
Nullpunktsverschiebungen in Frames
-
TRUE,TRUE,TRUE,T
RUE,TRUE,TRUE,TR
UE...
Bei inkrementeller Programmierung einer Achse wird nach einem Framewech-
Bei inkrementeller Programmierung einer Achse werden nach einem Frame-
-
DOUBLE
-
-
-
-
-
-
-
-
-
-
-
-
-
DOUBLE
-
-
-
-
-
-
-
-
-
-
-
-
-
BOOLEAN
-
-
NC-Settingdaten
3.1 NC-Settingdaten
N4
SOFORT
3/3
3/3
3/3
0/0
0/0
0/0
N4
SOFORT
3/3
3/3
3/3
0/0
0/0
0/0
K2
SOFORT
7/7
491
Werbung
Inhaltsverzeichnis
