Siemens SINAMICS S120 Handbuch Seite 313

24850
Grad
-
802d-cu3
802d-ng2
802d-ng3
802d-tm1
802d-tm2
802d-tm3
Beschreibung: Gibt für die 2. vereinbarte TRACYL-Transformation für jeden Kanal den Offset
der Rundachse in Grad gegenüber der Nullstellung an.
Nicht relevant:
wenn kein TRACYL aktiv
Korrespondiert mit:
MD24800 $MC_TRACYL_ROT_AX_OFFSET_1
24855
-
-
802d-cu3
802d-ng2
802d-ng3
802d-tm1
802d-tm2
802d-tm3
Beschreibung: 0:
1:
2:
Die ENS-Frames enthalten transformierte axiale Verschiebungen der Rund-
achse.
Maschinendaten und Nahtstellensignale
Listenhandbuch, 03/2011, 6FC5397-5CP10-3AA0
TRACYL_ROT_AX_OFFSET_2
Offset der Rundachse für die 2. TRACYL-Transformation
- 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
- 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
- 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
- 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
- 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
- 0.0,0.0,0.0,0.0,0.0,0.0,
0.0,0.0,0.0...
TRACYL_ROT_AX_FRAME_2
Rundachs-Verschiebung TRACYL 2
- 0,0,0,0,0,0,0,0,0,0,0,0,
0,0,0,0
- 0,0,0,0,0,0,0,0,0,0,0,0,
0,0,0,0
- 0,0,0,0,0,0,0,0,0,0,0,0,
0,0,0,0
- 0,0,0,0,0,0,0,0,0,0,0,0,
0,0,0,0
- 0,0,0,0,0,0,0,0,0,0,0,0,
0,0,0,0
- 0,0,0,0,0,0,0,0,0,0,0,0,
0,0,0,0
axiale Verschiebung der Rundachse wird nicht berücksichtigt.
axiale Verschiebung der Rundachse wird berücksichtigt.
axiale Verschiebung der Rundachse wird bis zum ENS berücksichtigt.
2.3 Kanalspezifische NC-Maschinendaten
C07
DOUBLE
- -
- -
- -
- -
- -
- -
C07
BYTE
0 2
0 2
0 2
0 2
0 2
0 2
Maschinendaten
M1
NEW CONF
2/2
-1/7
-1/7
0/0
2/2
2/2
-
NEW CONF
2/2
-1/7
-1/7
0/0
2/2
2/2
313