Ryobi RLT30CET Bedienungsanleitung Seite 27

EN
FR DE ES
You can often make adjustments and repairs described
here. For other repairs, have the trimmer serviced by an
authorised service dealer.
INSTALLING REEL EASY LINE TRIMMER HEAD
See Figures 5 .
Stop the engine and disconnect the spark plug wire.
Q
Remove currently installed line trimmer head.
Q
Open the Reel Easy Line Trimmer Head by
Q
depressing the latches on each side. The contents of
the line trimmer head are spring loaded, so keep your
other hand over the line trimmer head cover while
depressing the latches.
Remove the line trimmer head cover, knob, and spool
Q
and set aside.
Place the line trimmer head on the drive shaft. Make
Q
sure the line trimmer head is fully seated.
Install the hex bolt into the opening on the drive shaft
Q
and secure using the hex-shaped opening in the knob
to tighten.
NOTE: Only use the knob to tighten the bolt. The use
of other tools may allow over tightening of the bolt,
which could damage the line trimmer head.
Reinstall the spring into the line trimmer head and
Q
push down to seat.
Reinstall the spool. For the RLT30CET curved line
Q
trimmer attachment, the spool should be placed so
"This side out for curved shaft" is visible. If you are
using a straight shaft attachment with the Reel Easy
cutting head the spool should be placed so "This side
out for straight shaft" is visible.
Replace the knob in the spool.
Q
Replace the line trimmer head cover, aligning latches
Q
with openings in the line trimmer head. Press cover
and line trimmer head together until both latches snap
into openings securely.
Install line as described in the next section of this
Q
manual.
INSTALLING PRO CUT II TM LINE HEAD
See Figure 16.
Stop the engine and disconnect the spark plug wire.
Q
Remove currently installed line head.
Q
Install the line head on the drive shaft until fully
Q
seated.
Install the spool retainer and turn counter clockwise.
Q
Install cutting line as described in the next section of
Q
this manual.
INSTALLING CUTTING LINE IN PRO CUT II TM LINE
HEAD
See Figure 17.
Use monofilament line diameter 2.4mm or 2.7mm.
Use original manufacturer's replacement line for best
IT PT NL SV DA
English (original instructions)
NO FI HU CS RU
performance.
Stop the engine and disconnect the spark plug lead.
Q
Gather two of the pre-cut lengths of trimmer line
Q
provided or cut two pieces of trimmer line, in 28cm
lengths.
Insert the line into the slots located on the sides
Q
of the line head. Line should be pushed in until
approximately 2.5cm protrudes from the holes on the
top of the line head.
Remove old line by pulling it from the holes located on
Q
the top of the line head.
CLEANING THE EXHAUST PORT, MUFFLER AND
SPARK ARRESTOR
NOTE: Depending on the type of fuel used, the type
and amount of lubricant used, and/or your operating
conditions, the exhaust port, muffler, and/or spark
arrestor screen may become blocked with carbon
deposits. If you notice a power loss with your petrol
powered tool, you may need to remove these deposits
to restore performance. We highly recommend that only
qualified service technicians perform this service.
The spark arrestor must be cleaned or replaced every
50 hours or yearly to ensure proper performance of your
product. Spark arrestors may be in different locations
depending on the model purchased. Please contact
your nearest service dealer for the location of the spark
arrestor for your model.
IDLE SPEED ADJUSTMENT
See Figure 18.
If the cutting attachment turns at idle, the idle speed
screw needs adjusting on the engine. Turn the idle speed
screw counter clockwise to reduce the idle RPM and
stop the cutting attachment movement. If the cutting
attachment still moves at idle speed, contact a service
dealer for adjustment and discontinue use until the repair
is made.
WARNING:
The cutting attachment should never turn at idle.
Turn the idle speed screw counter clockwise
to reduce the idle RPM and stop the cutting
attachment, or contact a service dealer for
adjustment and discontinue use until the repair
is made. Serious personal injury may result from
the cutting attachment turning at idle.
CLEANING AIR FILTER SCREEN
See Figures 19 - 20.
For proper performance and long life, keep air filter
screen clean.
Remove the air filter cover by pushing down on the
Q
24
RO PL SL HR ET LT LV SK BG