Ryobi RLT30CET Bedienungsanleitung Seite 26

EN
FR DE ES
LINE TRIMMING CUT-OFF BLADE
See Figure 12.
The trimmer is equipped with a line trimming cut-off blade
on the grass deflector. For best cutting, advance line until
it is trimmed to length by the cut-off blade. Advance the
line whenever you hear the engine running faster than
normal, or when trimming efficiency diminishes. This will
maintain best performance and keep the line long.
STARTING AND STOPPING
See Figures 13 - 15.
When starting the line trimmer for the first time or
when the battery voltage is low, it may be necessary to
manually start the string trimmer.
FOR MANUAL START:
To start a cold engine:
DO NOT squeeze the throttle trigger until the engine
starts and runs.
Lay the trimmer on a flat, level surface.
Q
PRIME - Press the primer bulb at least 7 times, so
Q
fuel is clearly visible.
SET the start lever to the START position.
Q
Ensure the 'Ignition switch' (item 6) is in the centre
Q
position.
PULL the recoil starter until the engine starts.
Q
Wait 6-10 seconds, then gently squeeze the trigger to
Q
run.
NOTE: Squeezing and releasing the throttle trigger
releases the start lever to the RUN position.
To start a warm engine:
Make sure the 'ignition switch' is in the centre position.
Q
PULL the recoil starter until the engine starts.
Q
To stop the engine:
Press the 'ignition switch' (item 6) to the stop " O "
Q
position and the engine will stop.
FOR ELECTRIC START:
MAKE SURE THE BATTERY HAS BEEN FULLY
CHARGED - SEE CHARGING BATTERY
To start a cold engine:
DO NOT squeeze the throttle trigger until the engine
Q
starts and runs.
Install the battery onto the unit as shown in figure 8.
Q
Lay the trimmer on a flat, level surface.
Q
PRIME - Press the primer bulb at least 7 times, so
Q
fuel is clearly visible.
SET the start lever (item 21) to the START position on
Q
the side of the carburettor.
PRESS the 'safety switch' (item 19) and the 'ignition
Q
switch' to position 3 (item 6) at the same time.
IT PT NL SV DA
English (original instructions)
NO FI HU CS RU
The safety switch is a rocker type switch and will
Q
automatically reset it's self once released.
The ignition switch is a 3 position switch. position
Q
1 is 'off' position 2 is run, and position 3 is a
rocker type switch which will automatically reset
it's self to position 2 once released.
RELEASE the 2 switches after engine starts - they
Q
will revert back to their resting place.
Wait 6-10 seconds, then squeeze the throttle trigger to
Q
run.
NOTE: Squeezing and releasing the throttle trigger
releases the start lever to the RUN position.
To start a warm engine:
Lay the trimmer on a flat, bare surface.
Q
PRESS the 'safety switch' (item 19) and the 'ignition
Q
switch' (Item 6) at the same time.
RELEASE the 2 switches after engine starts - they
Q
will revert back to their resting place.
MAINTENANCE
WARNING:
When servicing, use only identical replacement
parts. Use of any other parts may create a hazard
or cause product damage.
WARNING:
Always wear safety goggles or safety glasses
with side shields during tool operation. If
operation is dusty, also wear a dust mask.
WARNING:
Before inspecting, cleaning, or servicing the
machine, shut off engine, wait for all moving parts
to stop, and disconnect spark plug lead and move
it away from spark plug. Failure to follow these
instructions can result in serious personal injury
or property damage.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, lubricant, grease.
WARNING:
Do not at any time let brake fluids, petrol,
p e t r o l e u m - b a s e d p r o d u c t s , p e n e t r a t i n g
lubricants, etc., come in contact with plastic
parts. Chemicals can damage, weaken or destroy
plastic which may result in serious personal
injury.
23
RO PL SL HR ET LT LV SK BG