Inhaltsverzeichnis
Werbung
10.00
; Sollwertausgabe simuliert:
$MA_CTRLOUT_TYPE[0,AX1]=0
$MA_CTRLOUT_TYPE[0,AX2]=0
$MA_CTRLOUT_TYPE[0,AX3]=0
$MA_CTRLOUT_TYPE[0,AX4]=0
$MA_CTRLOUT_TYPE[0,AX5]=0
$MA_CTRLOUT_TYPE[0,AX6]=0
$MA_CTRLOUT_TYPE[0,AX7]=0
$MA_CTRLOUT_TYPE[0,AX8]=0
; Achs–Ausgangssignale an PLC auch fuer simulierte Achsen
$MA_SIMU_AX_VDI_OUTPUT[AX1]=1
$MA_SIMU_AX_VDI_OUTPUT[AX2]=1
$MA_SIMU_AX_VDI_OUTPUT[AX3]=1
$MA_SIMU_AX_VDI_OUTPUT[AX4]=1
$MA_SIMU_AX_VDI_OUTPUT[AX5]=1
$MA_SIMU_AX_VDI_OUTPUT[AX6]=1
$MA_SIMU_AX_VDI_OUTPUT[AX7]=1
$MA_SIMU_AX_VDI_OUTPUT[AX8]=1
; der IPO–Takt wird dem Servo–Takt gleichgestellt
; deshalb wird $MA_FIPO_TYPE[AXn] = 1 fuer SIM ueberfluessig
$MN_IPO_SYSCLOCK_TIME_RA TIO=1
; Der einzig erlaubte und auch Defaultwert wird nicht extra gesetzt
; $MN_POSCTRL_SYSCLOCK_TIME_RATIO=1
; Spindel – Zustaende fuer IPO–Start abschalten
$MA_SPIND_ON_SPEED_A T_IPO_START [AX1] = FALSE
$MA_SPIND_STOPPED_AT_IPO_START [AX1] = FALSE
$MA_SPIND_ON_SPEED_A T_IPO_START [AX2] = FALSE
$MA_SPIND_STOPPED_AT_IPO_START [AX2] = FALSE
$MA_SPIND_ON_SPEED_A T_IPO_START [AX3] = FALSE
$MA_SPIND_STOPPED_AT_IPO_START [AX3] = FALSE
$MA_SPIND_ON_SPEED_A T_IPO_START [AX4] = FALSE
$MA_SPIND_STOPPED_AT_IPO_START [AX4] = FALSE
$MA_SPIND_ON_SPEED_A T_IPO_START [AX5] = FALSE
$MA_SPIND_STOPPED_AT_IPO_START [AX5] = FALSE
$MA_SPIND_ON_SPEED_A T_IPO_START [AX6] = FALSE
$MA_SPIND_STOPPED_AT_IPO_START [AX6] = FALSE
$MA_SPIND_ON_SPEED_A T_IPO_START [AX7] = FALSE
$MA_SPIND_STOPPED_AT_IPO_START [AX7] = FALSE
$MA_SPIND_ON_SPEED_A T_IPO_START [AX8] = FALSE
$MA_SPIND_STOPPED_AT_IPO_START [AX8] = FALSE
;Simulation ohne Getriebeumschaltung (setzt PLC–Quittung voraus !)
$MA_GEAR_STEP_CHANGE_ENABLE[ AX1 ]=0
$MA_GEAR_STEP_CHANGE_ENABLE[ AX2 ]=0
$MA_GEAR_STEP_CHANGE_ENABLE[ AX3 ]=0
$MA_GEAR_STEP_CHANGE_ENABLE[ AX4 ]=0
$MA_GEAR_STEP_CHANGE_ENABLE[ AX5 ]=0
$MA_GEAR_STEP_CHANGE_ENABLE[ AX6 ]=0
$MA_GEAR_STEP_CHANGE_ENABLE[ AX7 ]=0
$MA_GEAR_STEP_CHANGE_ENABLE[ AX8 ]=0
Siemens AG 2003 All Rights Reserved
SINUMERIK 840D/840Di/810D Funktionsb. Grundmaschine (FB1) – Ausgabe 11.2003
Dialogprogrammierung (D2)
2.5 Einrichten der Dialogprogrammierung
1/D2/2-25
Quicklinks ausblenden:
Werbung
Inhaltsverzeichnis
