(P052 = 5); (P052 = 20); Function Selection (P052) - Siemens SIMOVERT Master Drives 6SE70 Betriebsanleitung

Start-Up
4.3.9 Function selection
Function selection is activated via parameter P052 and permits various special functions during the start-up
phase.
Access stage 2 ( P051 = 2 ) must be enabled and the common rectifier may only be in the "Run" (R) status. Apart
from this, P053 must be set for parameter enable (e.g. P053=6).
The following functions are available:
The "Generate factory setting", "Forming", and "Circuit identification" functions are automatically reset on
completion, i.e. P052 = 0 ("Return").
The other functions must be manually reset!
4.3.9.1 Generate factory setting
This function is used to reset the parameter values, in accordance with a) the parameter list (dispatch status for
the unit; see Section 5, column 4) and b) parameter P077 (see below). Only the settings of parameters P070
(MLFB) and P077 (type of factory setting) remain unchanged.
The MLFB-dependent parameters P071, P075 and P076 are set in accordance with the type of the common
rectifier (see Section 4.3.9.2 "Initialization").
The parameters dependent on P077 are set in accordance with the table shown below.
In the normal case (P070=0), the values listed in the parameter list in Section 5 are used as factory settings, so
the table shown below does not have to be considered.
For fast parameterization of special functions, using P077=1 to 6, an appropriate set of factory settings can be
selected for certain parameters in accordance with the table shown below. In this manner, for example, certain
terminals of the basic unit can be parameterized fast as sources for certain control word functions.
The following table shows the factory settings for the parameters that are dependent on P077:
Para-
meters Designation of
depend. the parameter
on on OP1S
P077
P486 Src Current Setp
P554 Src ON/OFF1
P555 Src1 OFF2(electr.)
P561 Src InvRelease
P565 Src1 fault reset
P566 Src2 fault reset
P567 Src3 fault reset
P572 Src RegenRelease
P575 Src No ExtFault1
P583 Src 12-pulse mode
P587 Src Master/Slave
P588 Src No Ext Warn1
P607 Trg Bit Warning
The factory setting for P607.002 (responsible for the optional SCI1/2 module) is not affected by P077.
4-34
ENGLISH
(P052)
- Return from function selection
- Generate factory setting
- Initialization (MLFB setting)
- Download
- Hardware configuration
- Drive setting
- Forming
- Circuit identification
- Display modified parameters
(P052 = 1 or P970 = 0)
Standard
Normal
cubicle with
factory
terminals
setting
P077= 0 P077= 1
Basic Res. Basic Res.
(i001) (i002) (i001) (i002)
0 0 0 0
1010 1001 2001 1001
1010 1002 2001 1002
1 1 1 1
0 1003 0 1003
0 0 0 0
2001 2001 2001 2001
1 1 1 1
1 1 1 1
0 0 0 0
0 0 0 0
1 1 1 1
0 0
Standard Standard
cubicle with cubicle with
PMU OP1S
P077= 2 P077= 4
Basic Res. Basic Res.
(i001) (i002) (i001) (i002)
0 0 0 0
1003 1010 1003 2001
1003 1010 1003 2001
1 1 1 1
0 0 0 0
1004 0 1004 0
0 0 2001 2001
1 1 1 1
1001 1001 1001 1001
0 0 0 0
0 0 0 0
1002 1002 1002 1002
1001 1001
(P052 = 0)
(P052 = 1)
(P052 = 2)
(P052 = 3)
(P052 = 4)

(P052 = 5)

(P052 = 20)

(P052 = 21)
(P052 = 22)
Standard Standard
cubicle with cubicle with
PMU as OP1S as
12-pulse slave 12-pulse slave
P077= 5 P077= 6
Basic Res. Basic Res.
(i001) (i002) (i001) (i002)
6002 0 6002
6001 1010 6001 2001
6001 1010 6001 2001
6001 1 6001
0 0 0
6001 0 6001
2001 0 2001 2001
6001 1 6001
1001 1001 1001 1001
1 0 1
1 0 1
1002 1002 1002 1002
1001 1001
Siemens AG 6SE7087-6AK85-0AA0
Common Rectifier Operating Instructions
09.02
0
1
0
0
1
0
0