General Observation Parameters - Siemens SIMOVERT Master Drives 6SE70 Betriebsanleitung

Parameter List
PNU OP1S parameter name
Description
*
: Conf.
Par.
5.2

General observation parameters

r001 Status
Observation parameters for the current status of the S/F unit
0 = Enter MLFB (P070)
1 = Establish factory setting
2 = Hardware initialization
4 = Hardware settings
5 = Drive system settings
7 = Fault
8 = Restart inhibit
9 = Ready for turn-ON
10 = Wait for system voltage
11 = Ready for operation
12 = Ground fault test
14 = R/R unit is in operation
15 = Ramp generator decelerating (OFF1)
18 = Circuit identification or forming
21 = Download of parameter settings
PNU=1Hex; Type=O2; Scaling: 1Hex
r006 DC Bus Volts
Actual DC link voltage
PNU=6Hex; Type=I2; Scaling: 1Hex
r011 Heatsink Temp
Temperature of the heat sink
PNU=0BHex; Type=I2; Scalling: 1Hex
r012 Base/Reserve
Base / reserve settings of the process data wiring for control word bits
0: Base setting
1: Reserve setting
PNU=0CHex; Type=O2; Scaling: 1Hex
r013 Operat. Hours
Display of operating hours with firing pulses enabled (Run status).
All times > about 0.1s are taken into account.
i001 = days (0..9999)
i002 = hours (0..24)
i003 = seconds (0..3600)
The operating hours counter r013 is set to 0 when the factory setting is
established (P052=1).
PNU=0DHex; Type=O2; Scaling: 1Hex
r030 Rectifier Volts
Display of the system voltage at the rectifier bridge (phase W-U)
PNU=1EHex; Type=O2; Scaling: 1Hex
r031 Inverter Volts
Display of the system voltage at the regenerative bridge (average value of
the three phases)
PNU=1FHex; Type=O2; Scaling: 1Hex
5-4
ENGLISH
∧ 1
=
∧ 1 V
=
∧ 0 to 16384V
=
0 - 100%
∧ 1 °C
=
PZD gr.: 1
∧ +/-100 °C
=
Analog output: +/-100%
∧ 1
=
∧ 1
=
∧ 0.1 V
=
∧ 0 to 1638.4V
=
0 - 100%
∧ 0.1 V
=
∧ 0 to 1638.4V
=
0 - 100%
Value range
[phys. unit]
Selection text
0 to 21
(U) MLFB-Input
Init. RFE
(H) InitHW Conf
(H) HW Config.
(A) System Set.
(B) Fault
(B) ON Locked
(B) Ready for ON
(B) Line Voltage
(B) Ready Oper
(B) GrndFltTest
(R) Operation
(R) OFF 1
(R) Circuit ID
(B) Download
0 to 1000
[V]
-53 to 199
[°C]
0 to 1
d
h
s
0.0 to 1000.0
[V]
0.0 to 1000.0
[V]
Siemens AG
Common Rectifier
09.02
Display See
Indices Modify
Factory- (access /
setting status)
- 2/UHABR
- 2/ BR
-
- 3/ BR
-
- 2/ BR
-
3 2/ BR
-
- 2/ BR
-
- 2/ BR
-
6SE7087-6AK85-0AA0
Operating Instructions