Navigation Pilot - HBM WTX120 Bedienungsanleitung

1 Entry 2 Entry 3 Entry
Service Setup- Supervisor
Mode Level Mode
Standard
WTX120 V1.0 (Master = W1)
< 3 seconds < 3 seconds < 3 seconds
+
Password Password General Products
Enter service Enter service
password password
Date: Entry Target weight
Time: Entry ...
Filler configuration;
only available
in filler application
Service Mode
access
if no sensor
is connected
Interface
Com0 (Eth) Com1 (SIM1) Com2 (SIM2)
Port Baud Baud
Protocol Databits Databits
Parity Parity
Ctrl. Ctrl.
Protcl. Protcl.
Map symbology
Three diffrent possible entries
Entry field INFO level
Subsequent field INFO level
Related fields on INFO level
Enter password / Unload Scale
Mastermode
Click INFO button
Click respective grey button
Notes
hold + push to skip Switch from Master WTX120 to slaves
Weight Storage Logbook Software ID
Search Date 3_ ... ID: ...
Id-No. 2_ ...
Weight not found 1_...
General Calibration
note: if „S1" activated
only access,
no changes possible
Language
Keyboard
Time Zone (1)
Calibrate Scale 1
Time Zone (2)
Date (format only)
Time (format only)
Mastermode error protocoll,
Country Code
only info
note: alternative
Decimal char.
access
Approval signs
Tare mode
Cont. out.
Light off (Min.)
Power off (Min.)
Serial No.
exception: back to „Select Group 1 – 9" with
not with the INFO-Button
Select Group 1 – 9
Data Word Monitor
WTX120 Remote Control (slaves = WA, WB, ...) hex / dez
only available if WTX slaves are in the same
network and correctly assigned in
Service Mode / Config. / Config. Remote Ctrl.
Config. Test Reset Network
Test IP
Reset
G1 Parameters? Mask
Reset
Gate
Approved Wgt
DNS
NTP
FTP pwd
Access
Set PanelX password
Update SSL cert
Start auto ping
Terminal No.
Config. Config. Config.
Config. Scale
Digital IO Analog out Fieldbus
... PROFINET
Aout 1: Mode EtherNet-IP
Aout 1: Output Modbus-TCP
Aout 1: Calibration Profibus DP
+ address
1 Scale 2 Calibration 3 Linearization 4 Zero Adjust
Parameters
Geo Value New Fixpoint 1?
Unload Scale
Calibrate zero?
Calibrate load?
Single Range Dual Range Triple Range
High Cap. High Cap.
High Int. High Int.
Low Cap. Mid Cap.
Low Int. Mid Int.
Unit Low Cap.
Low Int.
Unit
One Interval Two Intervals Three Intervals Two Intervals T+
Capacity High Cap. High Cap. High Cap.
Interval High Int. High Int. High Int.
Unit Low Cap. Mid Cap. Low Cap.
Low Int. Mid Int. Low Int.
Unit Low Cap. Unit
Low Int.
Unit

Navigation Pilot

binär
Application
Backup General Setup Limit switches Digital IO
Backup or Application LS1 – LS4 Source Input 1 – 4
Restore
LS1 – LS4 Mode Output 1 – 4
from USB
note: after
change restart
only available in
required!
standard application
Language
Config.
Remote Ctrl
IP address 1
IP address 2
5 Adaption 6 High 7 Reset 8 Calculation
Resolution Span
Motion Windo Weight Reset Parameters? Calibrate Zero?
Motion Counter Zero (mV/V)
Filter Size LC-Cap. (kg)
Auto zero range No. of LCs
... mV/V of LC1
Power up zero
With Taring?
Underload
Update Rate
Three Intervals T+
High Cap.
High Int.
Mid Cap.
Mid Int.
Low Cap.
measure and predict with confidence
Low Int.
Unit
WTX120
Mastermode
Mode: Info Mode: Adapt
Factory defaults
(zero offset) (several
filter settings)
Load fact. Def.
Settings
9 W&M Info
W&M Setup ok