Herunterladen Inhalt Inhalt Diese Seite drucken

Preset Procedures Settings And Customization; Tip Illumination; Haptic Sense "Hs" - Activation Pedal And Pbm Adjustments - Ultradent Gemini EVO 810 Bedienungsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 23
CONTROLS, OPERATION & USE
When the system is in Active mode, touching any selection other than LEFT and RIGHT will return the system to the STBY mode. When the Activation Pedal is depressed in the Active mode, the outer
indicator lines around each wavelength icon on the display flashes to provide a visual indication that the laser is firing. There is also an audio beep when laser is being fired. For safety purposes, a laser
firing delay of 0.25 seconds was implemented in order to prevent accidental activation. (Figure: 6.2)
06 - PRESET PROCEDURE SETTINGS AND CUSTOMIZATION
Touch the PRESET selection to bring up all the preset procedures and categories on the display. A collection of pre-programmed procedures will be revealed on the display. Selecting the LEFT and RIGHT
arrows will toggle between NON SURGICAL, SURGICAL, and PAIN RELIEF categories. Selecting the UP and DOWN arrows will toggle between procedures within each category. The corresponding power
setting for each procedure is displayed on the Power Indicator when the procedure is highlighted. (Figure: 6.3, Option: 1)
A Simulated Screen showing the Gingivectomy Preset Procedure and dual wavelength mode selected. (Figure: 6.3)
The Gemini EVO 810+980 soft tissue laser is pre-programmed with 16 procedures listed under three categories: NON SURGICAL, SURGICAL, and PAIN RELIEF. Within each category are the most commonly
used procedures with suggested power settings. Always use the minimum amount of power necessary to perform a particular procedure. Manual power adjustment may be necessary depending on patient
and procedural needs.
NON SURGICAL
Decontamination
Aphthous Ulcer
Hemostatis
Debridement
SURGICAL
Incision / Excision
Implant Recovery
Tooth Exposure
Operculectomy
Gingivoplasty
Gingivectomy
Frenectomy
Pulpotomy
Troughing
PAIN RELIEF
7 mm Tip
3 mm Tip
25 mm Tip
Note: Preset procedure settings are only a general recommendation from the manufacturer. They are not meant to replace the need for proper training or clinical judgement of the operator. The presettings
are subject to changes through software updates and may therefore differ slightly from the settings indicated on this page. All power settings are shown in average power.
• Gemini EVO 810+980 soft tissue laser preset procedure settings can be customized. To save your own procedure setting, press PRESET (Figure: 6.3, Option: 2) once to bring up preset procedures on the
display and navigate to the procedure you would like to customize.
• When a particular procedure is highlighted, press and hold PRESET ICON for 3 seconds.
• You will hear two audible beeps and the power indicator value and power bar will start flashing on the display. Use LEFT/RIGHT arrows to adjust the new average power to the desired setting.
• To save the setting, press and hold the PRESET ICON for 3 seconds again. You will hear two audible beeps when the setting has been saved.
• To reset all preset procedure settings to the factory default, press and hold the PRESET ICON for 5 seconds. You will hear three audible beeps when the settings are reset.
• Another way to customize the preset procedures is through the DASHBOARD.
Hold 3 seconds = Customize / Save | Hold 5 seconds = Factory Reset
Power bar Indicator and power value will start flashing on the display. (Figure: 6.3, Option: 3)

07 - TIP ILLUMINATION

The Gemini EVO 810+980 soft tissue laser handpiece is equipped with a tip illumination light to provide better visibility of the surgical site during treatment. To toggle the light intensities between LOW,
MEDIUM, HIGH, and OFF, touch the MENU icon and select TIP LIGHT on the Guided Touch Interface. Then use the arrows UP / DOWN to change LED intensities. LED will only stay on for 3 seconds as a preview
when not in active mode. Tip Illumination icon shows Green color when this feature is enabled and Red when it is OFF.
Please note arrows UP / DOWN will appear and disappear according to the selected settings. As an example, if you select HIGH, the UP arrow will disappear indicating this is the highest setting available. The
same behavior happens when you select OFF, in which the DOWN arrow will disappear. (Figure: 6.4)
08 - HAPTIC SENSE "HS" - ACTIVATION PEDAL & PBM
The Gemini EVO 810+980 soft tissue laser is equipped with Haptic Sense "HS" in order to add an additional dimension of feedback while depressing the activation pedal or during PBM procedures. This feature
will provide the user a buzzing sensation to the foot or hand while the activation pedal is depressed. To toggle the Haptic Sense "HS" between activation pedal and handpiece (PBM procedures only), press
the haptic icon. Blue icon indicates Haptic Sense is available for activation pedal and Amber icon for handpiece (PBM procedures only). To adjust intensities between LOW, MEDIUM, HIGH, and OFF, touch the
arrows UP / DOWN to change the intensities. (Figure: 6.5)
TISSUE CONTACT
Yes
No
Yes
Yes
TISSUE CONTACT
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
TISSUE CONTACT
User Choice
User Choice
Spacer
810
DUAL
0.6w
0.5w
0.7w
0.6w
0.9w
0.8w
0.4w
0.3w
810
DUAL
1.1w
1.0w
1.3w
1.1w
0.8w
0.7w
1.2w
1.1w
0.8w
0.7w
1.0w
0.9w
1.2w
1.1w
0.8w
0.7w
0.9w
0.8w
810
DUAL
0.3w
0.3w
0.3w
0.3w
1.0w
1.0w
980
0.6w
0.8w
1.0w
0.5w
980
1.2w
1.5w
0.9w
1.4w
0.9w
1.1w
1.4w
1.0w
1.0w
980
0.3w
0.3w
1.0w
5

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Gemini evo 980

Inhaltsverzeichnis