Handpiece Magnet; Operating Mode; Emergency Stop; Remote Interlock - Ultradent Gemini EVO 810 Bedienungsanleitung

CONTROLS, OPERATION & USE
CAUTION: AVOID DAMAGING THE FIBER. Do not wrap the fiber in a counter-clockwise direction. Doing so will possibly damage the optical fiber, preventing the use of the laser.

16 - HANDPIECE MAGNET

The Gemini EVO 810+980 soft tissue laser is designed with a strong magnet that will secure the surgical handpiece in place when the laser is not in use. Gently place the handpiece behind the transparent
display or over the "rounded pad" of the laser unit and the magnet will hold the handpiece in place. (Figure: 10.1)
• Rounded ruberized pad (Figure: 10.1, Option: 1)
• Magnets (Figure: 10.1, Option: 2)

17 - OPERATING MODE

The Gemini EVO 810+980 soft tissue laser will only deliver energy in Pulsed "temporal emission mode" and is optimized to provide the operator ideal control of target tissue temperatures and efficiency of
energy delivered. The pulse width is fixed and not user adjustable. The operator will only need to adjust the laser wavelength and average power.

18 - EMERGENCY STOP

The Gemini EVO 810+980 soft tissue laser can be immediately deactivated in any mode, at any time, and in any power setting by pressing the red STOP button located in the front left of the system.
(Figure: 1.3, Option: 6)
19 - REMOTE INTERLOCK (SWITCH NOT INCLUDED)
The Gemini EVO 810+980 soft tissue laser provides a remote interlock feature that enables a clinician to establish a dedicated laser treatment room with a remote interlock connector. A switch on the entrance
door is attached and is electronically wired into the Laser Unit via 3.5 mm plug jack. When the door to the room is opened, the connector/switch provides an electrically open circuit that deactivates laser
emissions. To use the remote interlock feature, an interlock connector/switch and cable must be purchased. Contact the manufacturer for assistance. (Figure: 1.4, Option: 6)
Remote Interlock Symbol as it appears on display
20 - ADD NEW ACTIVATION PEDAL - BLUETOOTH CONNECTION
In certain instances, your office may need to have an additional Activation Pedal with the same Gemini EVO device. You can order an additional Activation Pedal and follow the instructions below to properly
pair the new pedal with your Gemini EVO unit. For a successful pairing, the sequence below must be followed:
1. Depress the Pedal (Figure: 11.1)
• If batteries are installed, remove both of them. Keep the pedal depressed until completion of STEP 3.
2. Install Batteries (Figure: 11.2)
• Keep the pedal depressed. Install the 2 batteries and keep the pedal depressed for 15 seconds.
3. Flashing Icons (Figure: 11.3)
• Activation Pedal icons will flash simultaneously along with the haptic feedback indicating pairing mode sequence has started. You can now release the pedal. (Figure 1.5, Options: 7-10)
4. Pairing
• Press and hold the HOME icon for 5 seconds.
• "Bluetooth Pairing Enabled" (Figure: 11.4)
• Activation Pedal automatically connects to your Gemini EVO device.
• "Bluetooth Pairing Successful" (Figure: 11.5)

21 - TRANSPARENT ELECTROLUMINESCENT DISPLAY

The Gemini EVO 810+980 soft tissue laser is designed with a unique transparent electroluminescent display that can provide extremely high resolution viewing angles from up to 160 degrees of field of view.
The transparent display was specially designed with over 80% transparency and an arch of 15 degrees for optimal viewing angle from any direction. The light is generated by a thin film, less than 2 microns
thick, of specially designed electroluminescent phosphor.
• Do Not Grab unit by display (Figure: 12.1)
• Grab unit by the base (Figure: 12.2)
DISPLAY SPECIFICATIONS
Display type: Electroluminescent
Transparency: 80%
Brightness: 300 cd/m^2
Color: Broadband Yellow
Peak Wavelength: 582 nm
Voltage: ~195V AC
Response time:
1.8 ms
Glass type: Soda lime
Glass thickness: 4.1 mm fused
Thin Film Thickness: ~2 micron
MOBILE APP & DASHBOARD
22 - ENABLING WI-FI CONNECTIVITY VIA APP
The Gemini EVO 810+980 soft tissue laser enables you to bridge your location's existing Wi-Fi network directly to the Gemini EVO unit. This provisioning enables your Gemini EVO unit to receive internet
connection, allowing the user to receive important performance updates, technical support, track procedures, and a multitude of other features.
To properly enable Wi-Fi connectivity, please follow the steps below:
3.5 mm Plug Port
9