Herunterladen Inhalt Inhalt Diese Seite drucken

Quick Start; Controls, Operation & Use; Electronic Key Passcode; Selecting A Wavelength - Ultradent Gemini EVO 810 Bedienungsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 23

QUICK START

1. DOWNLOAD THE MOBILE APP
2. PLUG IN POWER SUPPLY
During initial setup use the AC/DC power supply for at least one hour to fully charge the battery. Plug the power supply into an AC outlet and connect to the corresponding connector on the rear of the system.
(Figure: 2.2)
3. INSERT AA BATTERIES INTO ACTIVATION PEDAL
Install the (2) provided AA batteries into the wireless activation pedal. When replacing the AA batteries, we recommend an ALKALINE type battery. (Figure: 2.3)
4. TURN LASER UNIT ON
The universal ON/OFF button is a membrane switch that requires pressure in order to be activated. (Figure: 2.4)
5. ENTER ELECTRONIC KEY PASSCODE
Enter the electronic key passcode on the Guided Touch Interface using the Up and Down arrow keys. The security code sequence is UP, DOWN, UP, DOWN. A checkmark icon will appear when the correct key is
input. (Figure: 2.5)
6. SELECT YOUR DESIRED WAVELENGTH
Select the desired laser wavelength on the Guided Touch Interface: 810 nm, 980 nm, or Dual Wavelength. (Figure: 2.6)
7. SELECT YOUR DESIRED POWER SETTING
Select your desired power setting, then activate the laser. (Figure: 2.7)
CONTROLS, OPERATION & USE

01 - ELECTRONIC KEY PASSCODE

The Gemini EVO 810+980 soft tissue laser is equipped with an electronic key passcode. When you turn the Laser Unit on, the passcode key screen will be displayed at the bottom center of the screen.
The correct passcode sequence should be entered on the Guided Touch Interface: UP, DOWN, UP, DOWN. (Figure: 3.1, Options: 1, 2, 1, 2)
The Gemini EVO 810+980 soft tissue laser is equipped with Guided Touch Interface "GTI" which means only the icons that are relevant for a given procedure will be shown. When entering the electronic
key passcode, only the UP and DOWN arrows will be shown as they are the only necessary icons to be touched while entering the passcode.
THE GUIDED TOUCH INTERFACE AREA REQUIRES AN EXTREMELY LIGHT TOUCH TO WORK EFFECTIVELY.THE LIGHTER THE FINGER PRESSURE, THE MORE LIKELY IT WILL SENSE THE TOUCH.

02 - SELECTING A WAVELENGTH

When the system is turned on, and the electronic passcode is properly input, you will be prompted with voice confirmation "Please select wavelength" and two flashing wavelength graphics to select
the desired wavelength of choice. (Figure: 4.1) The Gemini EVO 810+980 soft tissue laser can operate in three wavelength modes: 810 nm alone, 980 nm alone, or Dual Wavelength. A wavelength mode
must be selected before proceeding further, but may be changed at any time. (Figure: 4.2)
By selecting the desired wavelength, voice confirmation (if enabled) will sound as follows: "810 STBY", "980 STBY" "DUAL WAVELENGTH STBY"
When selecting a wavelength, the 3 wavelength options 810 / DUAL / 980 will be shown as they are the only necessary icons to be touched while selecting a wavelength.

03 - ACTIVATION PEDAL CONNECTION

• Connecting the activation pedal to your laser unit via Bluetooth for the first time is simple. (See Figures: 5.1–5.8)
• Install the provided 2 AA batteries into the Activation Pedal. (Figure: 5.1)
• Turn the laser unit ON. (Figure: 5.2)
• Enter the Passcode. (Figure: 5.3)
• Select the wavelength of choice. (Figur: 5.4)
• Press Active to initiate the Bluetooth connection between the laser unit and pedal. (Figure: 5.5)
• Depress and release the Activation Pedal once. Connection is done automatically. (Figure: 5.6)
• A Bluetooth indicator will appear on the display and Activation Pedal when it is properly connected and the Laser is in Active mode. (Figure: 5.7)
• The Activation Pedal comes with a protective shroud to prevent accidental laser activation. Please do not step on the protective shroud as it could result in accidental damage to the Activation Pedal.
(Figure: 5.8)

04 - MANUAL POWER ADJUSTMENT

The Gemini EVO 810+980 soft tissue laser can output up to a maximum of 2.0 watts of average power. To adjust the power setting manually, touch the LEFT and RIGHT arrows on the Guided Touch
Interface. Each touch of an arrow raises or lowers the power by 0.1 watts. Touching and holding an arrow will increase the speed in which the power setting is raised or lowered. Touch the ACTIVE
button to put the laser in active mode. Depress the activation pedal to initiate the laser. (Figure: 6.1)
CLINICAL TIP
Optimal results will be achieved by regulating the power and the speed that the operator moves the fiber optic tip. Tissue charring is an undesirable after-effect of too much power or of the fiber tip
moving too slowly. Always use the least amount of power that is required to complete your procedure. The ideal tissue response will show little or no discoloration after treatment and will result in less
collateral damage and faster healing.
Avoid penetrating or damaging the periosteum, and do not attempt to use the laser on alveolar bone. Because the laser energy is attracted to melanin and hemoglobin, power must be reduced when
treating patients with darker pigmented soft tissue.

05 - LASER STBY AND ACTIVE MODES

The Active/STBY Guided Touch Interface selection serves a dual purpose. It activates (ACTIVE) and deactivates the laser (STBY). By default, the system powers up in STBY mode. The laser cannot be
activated prior to selecting a wavelength. Each time the ACTIVE/STBY selection is touched, the system toggles between Active and STBY modes. There is an audio confirmation (unless voice confirmation
is muted), and an icon for either "ACTIVE" or "STANDBY" near each wavelength indicator. The red aiming beam and tip illumination are visible only when the laser is in Active mode.
4
(Figure: 2.1)
"Please select wavelength"

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Gemini evo 980

Inhaltsverzeichnis