Siemens SINUMERIK 840D sl Handbuch Für Fortgeschrittene Seite 859

CEC_SCALING_SYSTEM_METRIC
CEC_TABLE_ENABLE
CEC_TABLE_WEIGHT
CENTRAL_LUBRICATION
CHAMFER_NAME
CHAN_NAME
CHANGE_LANGUAGE_MODE
CHBFRAME_POWERON_MASK
CHBFRAME_RESET_MASK
CHFRND_MAXNUM_DUMMY_BLOCKS
CHFRND_MODE_MASK
CHSFRAME_POWERON_MASK
CHSFRAME_RESET_CLEAR_MASK
CHSFRAME_RESET_MASK
CIRCLE_ERROR_CONST
CIRCLE_ERROR_FACTOR
CIRCLE_RAPID_FEED
CLAMP_POS_TOL
CLC_ACTIVE_AFTER_RESET
CLC_ANALOG_INPUT
CLC_AXNO
CLC_LOCK_DIR_ASSIGN_DIGOUT
CLC_OFFSET_ASSIGN_ANAOUT
CLC_PROG_ORI_ANGLE_AC_PARAM
CLC_PROG_ORI_AX_MASK
CLC_PROG_ORI_MAX_ANGLE
Ausführliche Beschreibung der Maschinendaten
Listenhandbuch, 02/2011, -
MD 32730 , 566
MD 32711 , 565
MD 41300 , 698
MD 41310 , 699
MD 12300 , 170
,
MD 10656 88
MD 20000 , 288
MD 9100 , 18
MD 24004 , 417
MD 24002 , 417
MD 20200 , 326
MD 20201 , 326
MD 24008 , 419
MD 24007 , 418
MD 24006 , 418
MD 21000 , 363
,
MD 21010 364
MD 55230 , 808
MD 36050 , 615
MD 62524 , 834
MD 62502 , 827
MD 62500 , 827
MD 62523 , 834
MD 62522 , 833
MD 62530 , 835
MD 62528 , 835
MD 62529 , 835
CLC_SENSOR_ACCEL_LIMIT
MD 62517 , 832
CLC_SENSOR_FILTER_TIME
MD 62525 , 835
CLC_SENSOR_LOWER_LIMIT
MD 62505 , 828
CLC_SENSOR_STOP_DWELL_TIME
MD 62521 , 833
CLC_SENSOR_STOP_POS_TOL
,
MD 62520 832
CLC_SENSOR_TOUCHED_INPUT
MD 62504 , 828
CLC_SENSOR_UPPER_LIMIT
MD 62506 , 828
CLC_SENSOR_VELO_LIMIT
MD 62516 , 831
CLC_SENSOR_VELO_TABLE_1
MD 62511 , 831
CLC_SENSOR_VELO_TABLE_2
MD 62513 , 831
CLC_SENSOR_VOLTAGE_TABLE_1
MD 62510 , 830
CLC_SENSOR_VOLTAGE_TABLE_2
MD 62512 , 831
CLC_SPECIAL_FEATURE_MASK
MD 62508 , 829
COLLECT_TOOL_CHANGE
MD 20128 , 313
COLLISION_INIT
MD 18950 , 287
COLLISION_TOLERANCE
,
MD 10619 84
COM_CONFIGURATION
MD 10161 , 39
COM_IPO_STRATEGY
MD 10073 , 28
COM_IPO_TIME_RATIO
MD 10072 , 27
COMP_ADD_VELO_FACTOR
MD 32760 , 568
COMPAR_ASSIGN_ANA_INPUT_1
MD 10530 , 76
COMPAR_ASSIGN_ANA_INPUT_2
MD 10531 , 77
COMPAR_THRESHOLD_1
MD 41600 , 706
COMPAR_THRESHOLD_2
MD 41601 , 706
COMPAR_TYPE_1
MD 10540 , 78
COMPAR_TYPE_2
Index
859