R R a a i i s s i i n n g g o o r r l l o o w w e e r r i i n n g g t t h h e e c c o o t t w w i i t t h h o o n n e e o o p p e e r r a a t t o o r r

You can raise or lower an unoccupied cot into a vehicle with one operator.

W W A A R R N N I I N N G G

• Always keep hands, fingers, and feet away from moving parts. Use caution when placing your hands and feet near the

base tubes while you raise or lower the cot.

• Always follow proper hand placement on hand grips. Keep all hands clear of the red safety bar pivots when you load or

unload the cot or change cot height position.

• Always remove your foot from the base tube when you are lowering the cot to the lowest position.

• Always keep hands away from the foot end release handle when you raise or lower the cot with the side release handle.

To raise or lower the cot:

From the foot end

1. Grasp the lower foot end lift tube.

2. Tip the cot up on its load wheels.

3. Squeeze and hold the release handle and raise or lower

the cot.

4. Release the release handle when you reach the desired

height.

5. Lower the cot back on onto the four base wheels.

L L o o a a d d i i n n g g o o r r u u n n l l o o a a d d i i n n g g a a c c o o t t w w i i t t h h t t h h e e P P o o w w e e r r - - L L O O A A D D o o p p t t i i o o n n

The cot is fully compatible with the Model 6390 P P o o w w e e r r - - L L O O A A D D system if you ordered the cot with the P P o o w w e e r r - - L L O O A A D D option

or upgraded your cot with the compatibility kit.

W W A A R R N N I I N N G G

• Always use P P o o w w e e r r - - L L O O A A D D with the 6085/6086 P P e e r r f f o o r r m m a a n n c c e e - - P P R R O O XT, 6500/6506 P P o o w w e e r r - - P P R R O O XT, and 6510/6516

P P o o w w e e r r - - P P R R O O IT cots with the P P o o w w e e r r - - L L O O A A D D option only. In certain situations, you can use P P o o w w e e r r - - L L O O A A D D as a standard

antler for most X-frame cots, but a rail clamp assembly is required for all cots without the P P o o w w e e r r - - L L O O A A D D option.

• Always make sure that you use a P P o o w w e e r r - - L L O O A A D D date of manufacture cot with the Stryker Model 6390 P P o o w w e e r r - - L L O O A A D D

system to avoid the risk of injury.

C C o o t t

Model 6506 P P o o w w e e r r - - P P R R O O XT

Model 6516 P P o o w w e e r r - - P P R R O O IT

Model 6086 P P e e r r f f o o r r m m a a n n c c e e - - P P R R O O XT

For more information about using your P P o o w w e e r r - - L L O O A A D D compatible cot, see the P P o o w w e e r r - - L L O O A A D D Operations Manual.

L L o o a a d d i i n n g g a a c c o o t t i i n n t t o o a a v v e e h h i i c c l l e e w w i i t t h h a a n n a a n n t t l l e e r r s s t t y y l l e e c c o o t t f f a a s s t t e e n n e e r r

Always load an occupied cot with a minimum of two trained operators. Two operators must be present when a cot is

occupied. Operators must be able to lift the total weight of the patient, cot, and any items on the cot.

W W A A R R N N I I N N G G

• Always support the load of the patient, cot, and accessories after the weight is off of the ground.

6086-209-005 Rev I.1

From the side

1. Place one foot on the outer base tube.

2. Grasp the side release handle with one hand. Place

your other hand on the outer support rail to stabilize the

cot.

3. Squeeze and hold the release handle and raise or lower

the cot.