Siemens SINAMICS S120 Handbuch Seite 227

>0.0 bedeutet, dass eine feste Reserve eingestellt wird (MD24720
$MC_TRAANG_PARALLEL_VELO_RES_1 * MD32000 $MA_MAX_AX_VELO der Parallelachse).
Das Geschwindigkeitsvermögen in der virtuellen Achse bestimmt sich daraus. Es
ist umso geringer, je kleiner MD24720 $MC_TRAANG_PARALLEL_VELO_RES_1 gesetzt
ist).
Korrespondiert mit:
MD24771 $MC_TRAANG_PARALLEL_ACCEL_RES_2
24721 TRAANG_PARALLEL_ACCEL_RES_1
- Beschleunigungsreserve der Parallelachse für 1. TRAANG-
Trafo
-
828d-me41 -
828d-me61 -
828d-me81 -
828d-te61 -
828d-te81 -
828d-te41 -
Beschreibung: Gibt für jeden Kanal für die erste TRAANG-Transformation die Beschleunigungs-
reserve für Jog-, Positionier- und Pendelbewegungen an, die auf der paralle-
len Achse (siehe MD2.... $MC_TRAFO_AXES_IN_...[1]) für die
Ausgleichsbewegung bereitgehalten wird.
Korrespondiert mit:
MD24720 $MC_TRAANG_PARALLEL_VELO_RES_1
24750 TRAANG_ANGLE_2
Grad Winkel zwischen kartesischer Achse und realer (schräger)
Achse
-
828d-me41 -
828d-me61 -
828d-me81 -
828d-te61 -
828d-te81 -
828d-te41 -
Beschreibung: Gibt für die zweite vereinbarte TRAANG-Transformation des Kanals den Winkel
der Schrägen Achse in Grad zwischen der 1. Maschinenachse und der 1. Basi-
sachse an, während TRAANG aktiv ist. Der Winkel wird positiv im Uhrzeigersinn
gezählt.
Korrespondiert mit:
MD24700 $MC_TRAANG_ANGLE_1
Maschinendaten und Nahtstellensignale
Listenhandbuch, 09/2011, 6FC5397-4DP40-2AA0
0.0,0.0,0.0,0.0,0.0,0.0, 0.0
0.0,0.0,0.0...
0.0,0.0,0.0,0.0,0.0,0.0, 0.0
0.0,0.0,0.0...
0.0,0.0,0.0,0.0,0.0,0.0, 0.0
0.0,0.0,0.0...
0.0,0.0,0.0,0.0,0.0,0.0, 0.0
0.0,0.0,0.0...
0.0,0.0,0.0,0.0,0.0,0.0, 0.0
0.0,0.0,0.0...
0.0,0.0,0.0,0.0,0.0,0.0, 0.0
0.0,0.0,0.0...
0.0,0.0,0.0,0.0,0.0,0.0, -
0.0,0.0,0.0...
0.0,0.0,0.0,0.0,0.0,0.0, -
0.0,0.0,0.0...
0.0,0.0,0.0,0.0,0.0,0.0, -
0.0,0.0,0.0...
0.0,0.0,0.0,0.0,0.0,0.0, -
0.0,0.0,0.0...
0.0,0.0,0.0,0.0,0.0,0.0, -
0.0,0.0,0.0...
0.0,0.0,0.0,0.0,0.0,0.0, -
0.0,0.0,0.0...
2.3 Kanalspezifische NC-Maschinendaten
C07 M1
DOUBLE NEW CONF
1.0 -1/7
1.0 -1/7
1.0 -1/7
1.0 0/0
1.0 1/1
1.0 -1/7
C07 M1
DOUBLE NEW CONF
- -1/7
- -1/7
- -1/7
- 0/0
- 1/1
- -1/7
Maschinendaten
M
M
M
S
M
M
M
M
M
S
M
M
227