Werbung
8 Störung und Abhilfe
ADM3 fault
code (J1939)
SPN / FMI
609 / 12
609 / 12
609 / 12
609 / 13
609 / 14
609 / 14
609 / 14
609 / 14
609 / 14
609 / 14
609 / 14
609 / 14
609 / 14
609 / 14
611 / 4
611 / 12
620 / 3
620 / 4
625 / 2
625 / 2
625 / 2
625 / 14
625 / 14
625 / 14
630 / 2
630 / 9
632 / 5
636 / 1
ADM3 operating manual rev. 10.00b
Kapitel 8
Störung und Abhilfe
ADM3
MR2
fault code
fault code
Fault location
(K-line)
(K-line)
-
14298
PLD/MR2 Bootloader
-
14299
PLD/MR2 Bootloader
PLD/MR2 Starter Relay
-
18039
Circuit
-
12400
PLD/MR2
-
14037
PLD/MR2 Program
-
14047
PLD/MR2 Program
-
14048
PLD/MR2 Program
-
14049
PLD/MR2 Program
-
14050
PLD/MR2 Program
-
14051
PLD/MR2 Program
-
14052
PLD/MR2 Program
-
14053
PLD/MR2 Program
Euromot3b / Tier4i
-
14269
Engine Control Module
-
19961
Anti Theft Device
-
16506
Oil Separator
-
16564
Oil Separator
Supply Analog
12103
-
Accelerator Pedal (AFP+)
Supply Analog
12104
-
Accelerator Pedal (AFP+)
CAN Link ADM3 –
12202
-
PLD/MR2
CAN Link ADM3 –
-
10102
PLD/MR2
CAN Link ADM3 –
-
10104
PLD/MR2
CAN Link ADM3 –
-
10100
PLD/MR2
CAN Link ADM3 –
-
10101
PLD/MR2
-
10149
PLD/MR2
-
14092
Control Module
-
14149
Control Module
Fuel Shutoff Valve "A"
-
12430
Control
Crankshaft Position
-
10310
Sensor "A"
Fault description
Flash Not Erasable
No Application Software
In Flash
Shorted (Main or
Redundant)
No. Of Cylinders Not
Corresponding To Engine
Type
Wrong No. of Cylinders
Set of Maps Error
Wrong No. of Cylinders
PWM Calibration
Wrong Hardware
EEPROM Checksum 1
EEPROM Checksum 2
EEPROM Checksum 3
Chassis Control Module
Mismatch
Immobilizer Response
Counter Flow
Circuit Low
Circuit High
Voltage too High
Voltage too Low
No Communication with
PLD/MR2
Invalid Data Received
No Communication
CAN B Bus (+) Circuit
CAN B Bus (-) Circuit
Control Module Vehicle
Options Error
Module Performance
Vehicle Options Error
Circuit Open
Circuit
Range/Perforamnce
350
9. Fault codes
Remedial action
New Since Version 10.00
- Supply voltage > 5,2 V.
- Supply voltage < 4,8 V.
- Check wiring (engine CAN)
- Check configuration: PLD/MR2
parameter (../..) and ADM3
parameter 01/01 to be set to
equal functionality (One wire
capability)
- Check wiring (engine CAN)
- Check wiring (engine CAN)
- Check wiring (engine CAN)
- Check wiring (engine CAN)
- Check Engine Brake
Parameters
Pin
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
21/09
21/09
-
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
LSCAN-
MR
157 / 226
Werbung
