Werbung
8 Störung und Abhilfe
8.7
9. Fault codes
8.7.1
9.1.
The background colour
The background colour
The background colour
broadcasted by the ADM over J1939.
ADM3 fault
code (J1939)
SPN / FMI
51 / 0
51 / 1
51 / 2
51 / 2
51 / 3
51 / 4
51 / 7
51 / 13
69 / 9
69 / 19
70 / 9
70 / 19
84 / 3
84 / 9
84 / 14
84 / 19
91 / 0
91 / 3
Kapitel 8
Störung und Abhilfe
ADM3 operating manual rev. 10.00b
Fehlercodes Dieselmotor Mercedes-Benz
Die Mercedes-Benz Fehlercodes werden vom ADM3-Rechner an das Farbterminal
gesendet und können dort abgelesen werden.
Der Fehlercode ist aufgeschlüsselt in die Bereiche:
SPN-Nummer/FMI-Nummer
Die folgende Liste ist ausschließlich zur Störungsbehebung durch speziell
unterwiesenes Fachpersonal gedacht. Deshalb wird sie von Mercedes-Benz
ausschließlich in englischer Sprache bereitgestellt.
Hiermit kann die Bedeutung von SPN/FMI entschlüsselt werden.
Fehlercodes der MB-Diagnoseversion 210
Fault codes diagnosis version 210
is used to indicate the newly supported or changed fault codes since diagnosis version 207.
is used to indicate the newly supported or changed fault codes since diagnosis version 210.
indicates PLD/MR2 fault codes which are received from the PLD/MR2 control unit and are
ADM3
MR2
fault code
fault code
(K-line)
(K-line)
-
12419
Engine Throttle Position
-
12420
Engine Throttle Position
-
12424
Engine Throttle Position
-
14217
Engine Throttle Position
Engine Throttle Position
-
14205
Sensor
Engine Throttle Position
-
14206
Sensor
-
12431
Engine Throttle Position
-
14218
Engine Throttle Position
17309
-
Two Speed Axle Switch
17319
-
Two Speed Axle Switch
17409
-
Parking Brake Switch
17419
-
Parking Brake Switch
Vehicle Speed (C3 or
10103
-
J1939)
Vehicle Speed (C3 or
10109
-
J1939)
Vehicle Speed (C3 or
10114
-
J1939)
Vehicle Speed (C3 or
10119
-
J1939)
Accelerator Pedal (AFPS
10200
-
or J1939)
Accelerator Pedal (AFPS
10203
-
or J1939)
Fault location
Fault description
Above Measuring Range
Below Measuring Range
Measuring Range Not
Plausible
Performance
Circuit High
Circuit Low
Defective
Position Not Learned
Abnormal Update Rate
Received Network Data
in Error
Abnormal Update Rate
Received Network Data
in Error
Open Circuit
Abnormal Update Rate
Signal Not Plausible
Received Network Data
in Error
Not Adjusted
Voltage too High
344
9. Fault codes
Remedial action
LSCAN-
LSCAN-
LSCAN-
LSCAN-
LSCAN-
LSCAN-
LSCAN-
LSCAN-
CAN-
J1939
CAN-
J1939
CAN-
J1939
CAN-
J1939
- Check wiring
15/03
CAN-
J1939
- Check wiring
15/03
CAN-
J1939
- Restart accelerator pedal
adjustment routine
- Check wiring
- Limit value idle operation
21/11
position: 5,0 V
- Limit value kickdown position:
4,9 V
- Pedal unit exchange, if
defective
- check wiring
- Limit value idle operation
21/11
position: 5,0 V
- Limit value kickdown position:
4,9 V
151 / 226
Pin
MR
MR
MR
MR
MR
MR
MR
MR
Werbung
