Redmond RMC-M23E Handbuch Seite 6

Model RMC-M13E RMC-M23E
Bowl type RB-C302 RB-C502
5. Housing
6. Container for condensate collection
7. Control panel with display
8. Adjustment ring
9. Power switch
10. Lid release button
11. Steaming container
12. Measuring cup
13. Serving spoon
14. Stirring paddle
15. Power cord
Elements of control panel
A2
1. Display.
2. Cooking programmes indicators.
3. "Hour/Min" button— switches on current time adjustment mode; to select
hour/minute value in current time adjustment modes, cooking time and
time delay.
4. "Reheat" button — to enable Reheat function (in standby mode).
5. "Start/Keep Warm" button with "Start" and "Keep Warm" indicators— to
start cooking programme; to disable Keep Warm in advance.
6. Adjustment ring: to select cooking programme; to adjust current time/
cooking time/ time delay; to adjust temperature in "MULTICOOK" pro-
gramme. Turn the ring clockwise to increase the value, turn the ring
counterclockwise to reduce the value. 16 switches per 360°degree rotation
may be performed.
7. "Keep Warm" indicator is lit up when Keep Warm mode is enabled.
8. "Cancel" button — to stop cooking programme operation; to clear previous
settings; to enable/disable audible signals (in standby mode).
9. "Set" button — to enable parameter adjusting mode; to switch to cooking
temperature adjusting mode (in "MULTICOOK" programme) / Time Delay.
10. "Start" indicator lights up during cooking programme operation and Time
Delay; is flashing when reaches operating temperature in "RAVIOLI",
"PASTA" и "DUMPLINGS" programmes.
Display
A. "Timer" indicator — is lit when adjusting cooking time/ during programme
operation.
B. "Time Delay" indicator — is lit when adjusting Time Delay / during appliance
operation in Time Delay.
C. Disabled audible signals indicator.
D. Keep Warm indicator.
E. "Reheat" indicator — is lit during Reheat function operation.
F. Temperature value indicator in "MULTICOOK" programme.
I. PRIOR TO THE FIRST USE
Carefully unpack the device, remove all packaging materials and stickers except
the one with the unit's serial number.
The absence of the serial number will deprive you of your warranty benefits.
Wipe all interior and exterior surfaces of the unit with a soft, damp cloth. Wash
the bowl in warm soapy water. Rinse and dry thoroughly. Odor on first use of the
appliance is normal. In such case, clean the device
6
After transportation or storage at low temperature allow the appliance to stay
RMC-M33E
at room temperature for at least 2 hours before use.
RB-C602
II. OPERATION
Before Use
Place the device on a flat, stable, and hard surface away from wallpaper, decora-
tive coatings, or any other objects or cabinets that could be damaged by steam,
humidity, or high temperatures. Before operating the appliance, ensure that the
outer and inner parts of the pressure multicooker have no dents, cracks or any
other visible damages. There should not be any obstructions between the heat-
ing element and the bowl.
Standby mode
The plugged in appliance has default standby mode setting; current time is
displayed in 24-hour format. If no button was pressed during one minute when
setting selected programme parameters, the appliance will switch to the stand-
by mode; all the previous settings will be cleared.
To adjust the clock
To adjust the current time:
1. Press and hold "Hour/Min" button for several minutes in standby mode.
indicator will be lit on the display; clock register indicator will be
flashing.
2. Select clock value rotating adjustment ring this or other way. Repress
"Hour/Min" button to switch the register and turning the adjustment ring
adjust the minute value. After maximum value is reached the adjustment
starts from beginning of the adjustment range.
3. When time adjusting is complete do not press any buttons. The adjusted
time value will be saved in a few seconds.
Enable/disable audible signals
The REDMOND RMC-M13E/RMC-M23E/RMC-M33E multicookers allow to enable/
disable audible signals, that accompany pressing the buttons and the end of
cooking process. To disable/enable audible signals press and hold "Cancel" but-
ton in standby mode.
Non-volatile memory
The REDMOND RMC-M13E/RMC-M23E/RMC-M33E multicookers have non-vol-
atile memory. If power failure occurs during programme operation (up to 15 min-
utes in cooking mode) the appliance saves all settings to the memory. The ap-
pliance will start operation on the interrupted stage. Press the "Cancel" button
if it is undesirable to the continue cooking process. The appliance will switch to
the standby mode.
To adjust cooking time
The REDMOND RMC-M13E/RMC-M23E/RMC-M33E multicookers provide default
cooking time adjusting. Time interval and range depend on selected cooking
programme.
1. Select the programme rotating the adjustment ring this or that way.
The "Timer" indicator will be lit on the display, default cooking time will
be displayed for every programme.
2. Press the "Set" button. The clock register indicator will be flashing.
3. Select the time value rotating adjustment ring this or that way. Repress
the "Hour/Min" button to switch the register and adjust minute value
turning the adjustment ring. After the maximum value is reached in
every register the adjustment starts from beginning of the adjustment
range.
.
Time Delay
The time delay function allows adjusting time by which the dish will be ready.
The maximum time of delay is 24 hours in 15 minutes interval. It should be
taken into account that Time of delay should be more than adjusted cooking
time otherwise the programme will start the operation after pressing the "Start/
Keep Warm" button.
1. Select the programme, adjust the cooking time if necessary. Adjust
the cooking temperature for the "MULTICOOK" programme.
2. Press the "Set" button. The "Time Delay" and the time value indicators will
be flashing.
3. Adjust the time value rotating the adjustment ring. Repress the "Hour/
Min" button to switch the register and adjust the minute value turning
the adjustment ring. After the maximum value is reached in every register
the adjustment starts from beginning of the adjustment range.
4. Press the "Start/Keep Warm" button. The appliance will switch to the Time
Delay mode, the "Time Delay" and the current time indicators will be lit.
Press the "Hour/Min" button to see the adjusted time by which the food
will be ready.
5. Press the "Cancel" button to clear the current settings. The cooking pro-
gramme should be adjusted all over again.
Avoid using the Time Delay function for perishable products.
The Time Delay function is not applicable for the «EXPRESS», «SAUTÉ»,
«RAVIOLI», «PASTA», «DUMPLINGS», «CRUST» programmes.
Keep Warm function
This function automatically activates in the end of cooking cycle and keeps the
food warm at 70-75°С for 12 hours. Direct countdown is lit on the display. To
disable the Keep Warm press and hold the "Start/Keep Warm" button (the "Keep
Warm" indicator will go out).
Though Keep Warm mode is designed for 12 hours, it is not recommended to
leave food heated for a long time, as it may lead to food overdrying and change
in its taste qualities.
The Keep Warm mode is not applicable for the «EXPRESS», «YOGURT», «YEAST
DOUGH», «VACUUM», «RAVIOLI», «PASTA», «DUMPLINGS», «CRUST» pro-
grammes.
In «BREAD» programme Keep Warm operation is 3 hours, in «BAKE» and «PIE»
programmes — 4 hours.
Keep Warm disabled in advance
The Keep Warm mode may be disabled in advance if necessary. To do so after the
start of cooking programme repress and hold the "Start/Keep Warm" button
until the "Keep Warm" indicator goes out.
In the same manner the Keep Warm function may be activated again (the "Keep
Warm" indicator will be lit up solid).
When cooking at the temperature below 80°С the Keep Warm function has a
default block setting for your accommodation. It can be manually adjusted by
pressing the "Start/Keep Warm" button after the start of cooking programme
if necessary (the "Keep Warm" indicator will be lit up solid).
Reheat
Provides reheating cold meals:
1. Fill the bowl with food and position it inside the appliance. Ensure it is
tightly connected to the heating element.
2. Close the lid until it clicks into place. Plug in the appliance.
3. Press the "Reheat" button. The "Reheat" indicator will light up solid, the
"Reheat" function will be activated and direct minute countdown will start.