Olympus WS-331M Bedienungsanleitung Seite 7

My Computer, in the window, the
recorder will appear as a removable disk.
4. Transfer the audio files to your computer.
The 5 voice folders of this recorder are
displayed as "DSS_FLDA", "DSS_FLDB",
"DSS_FLDC", "DSS_FLDD" and "DSS_
FLDE", and the recorded voice files are
saved in WMA format in these folders.
You can copy them to any folder on your
computer. While transmitting data, "Busy" is displayed, and the
record/play indicator light and USB access indicator light flashes
red. If you double-click on the file, Windows Media Player will be
launched and playback will start.
Notes
• If you are using Windows 2000, Windows Media Player must be
installed on the PC.
• If you leave the battery compartment disconnected from the recorder
for a longer period of time or if you remove the battery compartment
repeatedly at short intervals, you may have to reset the time
(+ P. 17).
Disconnecting from Your PC
1. Click the on the task bar located at the lower-right corner of
the screen. Click [Safely Remove Hardware]. The drive letter will
differ depending on the PC being used.
2. When the safe to remove hardware window appears, click [OK].
3. Make sure that the display is turned off, disconnect the USB.
4. Connect the battery compartment to the main unit. Leave
the HOLD switch in its disabled position ( + P. 75) when
connecting the battery compartment.
Notes
• NEVER disconnect the USB while the record/play indicator light and
USB access indicator light are flashing in red. If you do so, the data
may be destroyed.
• Refer to the user's manual for your PC regarding the USB port or USB
hub on your PC.
• Be sure to push the USB connector all the way in. Otherwise, the
recorder may not operate properly.
• Use the supplied USB extension cable depending on situations.
• Do not use USB extension cables other than the supplied cable.
Using cables from other manufacturers could result in damage to the
recorder. Do not use the supplied USB extension cable with devices
from other manufacturers.
Erasing
n Erasing (Fig. 12)
Erasing One File at a Time
A selected file can be erased from a folder.
1. Select the file you want to delete. In the stop
status, display the file or place the cursor on
the file in the list display.
2. Press the ERASE button. The "Cancel"
indicator flashes.
3. Press the + button to choose "Erase".
3 4. Press the OK button. The display changes
"Erase Done" is displayed when the file is
erased. File numbers will be reassigned
automatically.
Erase All Files from a Folder
All files in a folder can be erased
simultaneously. The locked files ( + P. 40)
and the files set to read-only on the PC will
not be erased.
1. Press the FOLDER button to select the folder
2. Press the ERASE button twice. The "Cancel"
3. Press the + button to choose "All Erase".
4. Press the OK button. The display changes to
"Erase Done" is displayed when the files are
erased. The locked files and read-only files are
reassigned the file numbers in ascending order,
starting from "1".
Notes
• An erased file cannot be restored.
• The locked files and the files that are set to
read-only will not be erased (+ P. 40).
• If an action is not selected within eight seconds
on the "Cancel", "Erase", or "All Erase"
screens, the recorder will return to stop status.
• It may take over 10 seconds to complete
erasing. Never turn the power off or remove
batteries during this time because data may
be corrupted.
Hold
If you bring the HOLD switch to the HOLD position, the current
conditions will be preserved, and all buttons and switches will be
disabled.This feature is useful when the recorder has to be carried
in a bag or pocket.
1. Set the Recorder to HOLD Mode
Slide the HOLD switch in the direction indicated
by the arrow while the recorder is not in
operation. After "Hold" appears on the display,
the recorder is set to HOLD mode.
2. Exit HOLD Mode
Slide the HOLD switch in the direction opposite that indicated by
the arrow.
Notes
• If you press any button in HOLD mode, the clock display flashes for
2 seconds, but it will not operate the recorder.
• If HOLD is applied during playback (recording), operation is disabled
with the playback (recording) state unchanged. (When playback ends,
33
120
XQ
or recording ends due to insufficient memory, the recorder will stop
E r a s e
once, then will automatically enter in hold status.)
C a n c e l
33
120
E r a s e
C a n c e l
to "File Erase!" and erasing will start.
in which you want to erase all files.
indicator flashes.
"All Erase!" and erasing will start.
(Fig. 13)
33
120
F i l e
E r a s e !
33
119
XQ
E r a s e
D o n e
120
XQ
A l l E r a s e
C a n c e l
120
A l l E r a s e
C a n c e l
120
A l l
E r a s e !
00
00
XQ
E r a s e
D o n e
H o l d
EN 11