Assembling The Pressure Regulator And Lid Handle; Storage; Maintenance & Spare Parts; Notes On Replacing Parts - Fissler vitaquick Gebrauchs- Und Pflegehinweise

EN
recommended by the manufacturer, do not use industrial detergents or highly
concentrated cleaners

Assembling the pressure regulator and lid handle

Pressure regulator (Fig. A-4)
Removal:
See Figure R
Loosen the fastening screw (Fig. A-24) by turning it counterclockwise and remove the
pressure regulator. The fastening screw can be loosened without tools using a coin.
Assembly:
See Figure S
Insert the pressure regulator (1) into the specified position in the lid from above (in the
center on the bolt), screw on the fastening screw (2) clockwise from below and tighten it
firmly.
Lid handle (Fig. A-9)
Removal:
See Figure T
Loosen the cover handle by turning the fastening screw (Fig. A-22) on the inside of the lid
counterclockwise.
Assembly:
See Figure U
Hold the lid handle in your hand and place the lid in the specified position.
Turn the fastening screw clockwise and tighten it firmly.

Storage

The sealing ring should be stored in a clean, dry and dark (protected from sunlight and UV
radiation) place.
To protect the sealing ring and avoid crushing it, place the lid upside down on the pot after
cleaning.
9. Maintenance & spare parts
WARNING!
• Wear parts such as the sealing ring and other rubber parts must be replaced
regularly, i.e. after a maximum of 400 cooking processes or after 2 years at the
latest, with original Fissler spare parts. Parts that show visible damage (e.g.
hardening, cracks, discoloration or deformation) or those that do not fit correctly
must also be replaced immediately.
Non-compliance can negatively affect the functioning and safety of your pressure
cooker. If you have any questions, please contact our customer service or
the staff at your specialist retailer.
38

Notes on replacing parts

Sealing ring (Fig. A-23)
See chapter 5.
Rolling diaphragm (Fig. A-17)
See Figure V
Detach the pressure regulator from the lid and pull off the old rolling diaphragm.
Place the new rolling diaphragm into the hole in the lid from the inside. Check if it fits
correctly by rotating it.
Assemble the pressure regulator (see chapter 8)
Pressure regulator (Fig. A-4)
See Figure W
Loosen the fastening screw (Fig. A-24) by turning it counterclockwise and remove the
pressure regulator. The fastening screw can be loosened without tools using a coin.
Assembly:
See Figure S
Insert the pressure regulator (1) into the specified position in the lid from above (in the
center on the bolt), screw on the fastening screw (2) clockwise from below and tighten it
firmly.
Valve seat seal (Fig. A-19)
See Figure X
Remove the pressure regulator from the lid and pull off the old seal.
Insert the new seal and ensure that the seal is positioned properly and in a flat position on
both sides of the lid.
O-ring for Euromatic (Fig. A-21)
See Figure I
Disassembly/assembly is carried out on the inside of the lid. Make sure that the seal is
positioned completely in the groove provided for it.
Euromatic (Fig. A-21)
To disassemble/assemble the Euromatic, you must first remove the lid handle. To do this,
you only need to loosen the screw on the inside of the lid. Once you have removed the
O-ring, you can remove the Euromatic from the lid. To assemble the new Euromatic, guide
it through the lid without the O-ring, so that the side with the white ball is on the inside of
the lid. Then, fit the O-ring as described above.

Spare parts

Spare part ..........................................................Diameter .......... Item number
Helper handle for pressure skillet (Fig. Y-3) ................... 22 cm ................... 600-300-02-840
................................................................................................ 26 cm ................... 600-700-04-840
Helper handle for pressure cooker (Fig. Y-3) ................. 22 cm ................... 600-300-04-840
................................................................................................ 26 cm ................... 600-700-08-840
Lid handle (Fig. Y-4) ............................................................ all ........................... 600-000-11-770
Fastening screw for the lid handle
EN
DE
EN
FR
ES
IT
NL
RU
GR
TR
KO
ZH
JA
PL
CZ
SR
HR
HU
SK
SL
RO
BL
AR
39