Scheppach PCS26 Originalbetriebsanleitung Seite 47

13.13 Service information
With this product, it is necessary to note that the follow-
ing parts are subject to natural or usage-related wear,
or that the following parts are required as consumables.
Wearing parts*: Saw chain, guide rail, chain oil, en-
gine oil, spark plug, air filter, fuel filter, chain oil filter
* may not be included in the scope of delivery!
Spare parts and accessories can be obtained from
our Service Centre. To do this, scan the QR code on
the front page.
Approved cutting gear
Saw chain
Kangxin 3/8LP-40 ...................................7910100739
Oregon 91P040X .....................................3910102032
Guide rail
Kangxin AP10-40-509P .......................... 7910100740
Oregon 100SDEA041 .............................7910100744
14. Storage
The spark plug wrench / slotted screwdriver (20) can
be attached to the side of the guide rail cover (21) for
storage.
Always use the guide rail cover (21) when storing.
Clean and maintain the device every time before stor-
age (see chapter "Cleaning and maintenance").
Empty the oil or fuel tank completely.
WARNING
Do not remove the petrol in enclosed spaces, near
fire or when smoking. Petrol fumes can cause explo-
sions and fire.
• Start the engine and let it run until the remaining
petrol is used up.
Store the device and its accessories in a dark, dry and
frost-free place that is inaccessible to children. The
optimum storage temperature is between 5 and 30˚C.
Do not store and use the chainsaw at temperatures
below 0°C!
Never store a chainsaw for longer than 30 days with-
out carrying out the following steps.
Follow the cleaning and maintenance information be-
fore storing the unit!
14.1 Stowing the chainsaw
If you store a chainsaw for longer than 30 days, it
must be prepared ahead of time. Otherwise, the re-
maining fuel in the carburettor will evaporate and
leave a rubbery sediment behind. This could make
it difficult to start and result in expensive repair work.
1. Slowly remove the fuel tank cap (13) to release
any pressure in the tank. Carefully empty the tank.
2. Start the engine and let it run until the chainsaw
stops in order to remove the fuel from the carbu-
rettor.
3. Allow the engine to cool down (approx. 5 minutes).
4. Remove the spark plug (34).
5. Add 1 teaspoon of clean 2-stroke oil to the com-
bustion chamber. Pull the start pull cord (8) slow-
ly several times to coat the internal components.
Re-insert the spark plug (34).
Store the chainsaw in a dry location and far away
from potential sources of ignition, such as furnaces,
hot water boilers with gas, gas dryers, etc. out of the
reach of children.
Always fit the guide rail cover (21) if the saw chain (1)
and the guide rail (2) are not removed
14.2 Recommissioning the chainsaw
1. Remove the spark plug (34).
2. Pull the start pull cord (8) quickly to remove ex-
cess oil from the combustion chamber.
3. Clean the spark plug (34) and check that the elec-
trode gap on the spark plug (34) is correct is cor-
rectly set, or insert a new spark plug (34) with the
correct electrode gap.
4. Prepare the chainsaw for operation.
5. Fill the tank with the correct oil and fuel mixture
(1:40).
14.3 Fuel storage
Fuels only have a limited shelf life. Fuel and fuel mix-
tures age by evaporation, especially under the influ-
ence of high temperatures. Expired fuel and fuel mix-
tures can thus lead to starting problems and engine
damage. Only buy as much fuel as is to be consumed
in a few months. Use up fuel mixed at higher temper-
atures in 6-8 weeks.
Store fuel only in approved containers in a dry,
cool and safe place!
WARNING
Avoid skin and eye contact!
Mineral oil products, including oils, degrease the skin.
Repeated and prolonged contact dries out the skin.
The consequences can be various skin diseases. Al-
lergic reactions are also known.
Eye contact with oil causes irritation. In case of eye
contact, immediately rinse the affected eye with clean
water. If irritation persists, consult a doctor immedi-
ately!
www.scheppach.com
GB | 47