Scheppach PCS26 Originalbetriebsanleitung Seite 37

■ Tensioned wood must always be cut on the com-
pressed side first. Only then perform the separat-
ing cut using the opposite side. This prevents the
rail from jamming.
■ When working in the tree, the chainsaw may fall
down. People can be seriously injured and material
damage can occur. Secure the chainsaw using the
suspension device.
■ Before the saw chain is guided into the cutting area,
it can slip away to the side or jump up.
m ATTENTION
Increased risk of kickback!
In order to maintain full control at the moment of "cut-
ting all the way through", reduce the pressing force
towards the end of the cut, without loosening your
firm grip of the handles of the chainsaw. Ensure that
the saw chain does not come into contact with the
ground. After completing the cut, wait for the saw
chain to stop before removing the chainsaw. Always
switch off the chainsaw's engine before moving from
one tree to the next tree.
m WARNING
In case of extended working periods, the operating
personnel may suffer circulatory disturbances in their
hands (vibration white finger) due to vibrations.
Raynaud's syndrome is a vascular disease that caus-
es the small blood vessels on the fingers and toes to
cramp in spasms. The affected areas are no longer
supplied with sufficient blood and therefore appear
extremely pale. The frequent use of vibrating devices
can cause nerve damage in people whose circulation
is impaired (e.g. smokers, diabetics).
If you notice unusual adverse effects, stop working
immediately and seek medical advice.
Observe the following information to reduce hazards:
• Keep your body and especially your hands warm in
cold weather.
• Take regular breaks and move your hands to pro-
mote circulation.
• Ensure as little vibration as possible at the device
via regular maintenance and stable parts on the
machine.
7.10 Residual risks
m DANGER
DANGER OF INJURY!
Contact with the saw chain can lead to fatal cuts.
Never touch the saw chain with your hands while it
is running.
DANGER OF KICK-BACK!
Kick-back can lead to fatal cuts.
DANGER OF BURNS!
The chain and guide rail heat up during operation.
The device is state-of-the-art and has been built
in accordance with the recognised technical
safety rules. However, individual residual risks
can arise during operation.
Furthermore, despite all precautions having been
met, some non-obvious residual risks may still re-
main.
Residual risks can be minimised if the "safety instruc-
tions" and the "Proper use" are observed along with
the whole of the operating instructions.
8. Technical data
Machine without saw bar
Length x width x height ..............270 x 230 x 240 mm
Weight unfuelled, without
set of blade and saw chain approx....................3.4 kg
Weight unfuelled, with set of blade
and saw chain approx. ......................................3.8 kg
Tank for chain lubricating oil .............................. 0.16 l
Fuel tank contents ..............................................0.23 l
Oil and fuel mixture ..............................................1:40
Cutting length ....................................................20 cm
Saw bar length ..................................................30 cm
Automated chain oiling .......................................... yes
Chain pitch ........................................3/8" (9.525 mm)
Chain link thickness ......................................1.27 mm
Chain type ....................................................3/8LP-40
Number of drive sprocket teeth .................................6
Drive sprocket tooth pitch..................................... 3/8"
Saw bar type ...................................... AP10-40-509P
Max. chain speed .............................................21 m/s
Engine ........................ 1 cylinder, 2 stroke air-cooled
Engine cubic capacity .................................. 25.4 cm³
Max. engine power output per ISO 7293 ........ 0.7 kW
Idle speed n
Maximum speed with
set of blade and saw chain ........................ 11000 rpm
Spark plug ....................................................... L8RTC
Noise
Measured sound pressure level L
Uncertainty K
Guaranteed sound power level L
Measured sound power level L
Uncertainty K
Information on the noise emissions as per the Prod-
uct Safety Act (ProdSG) and EC machinery directive:
The noise pressure level at the workplace can ex-
ceed 80 dB.
www.scheppach.com
.....................................3300 ± 300 rpm
0
............... 99.2 dB
pA
.................................................... 3 dB
pA
..................113 dB
WA
................. 108.7 dB
WA
................................................... 3 dB
WA
GB | 37