Starting The Oven - Moretti Forni T Serie Bedienungsanweisung

3.2 STARTING UP
WARNING!
- Never allow unauthorized persons to approach the oven.
- Take particular care never to touch moving parts with your arms, hair,
bracelets, rings, tools, clothing, etc. or with any parts that might become
hooked up, because in spite of the low speed at which the conveyor belt
turns there is a risk of being dragged and crushed by movement of the
belt itself.
- In particular, bear in mind that the glass in the front door, the
adjustable side walls and the conveyor belt heat up when the oven is in
use, and must never be touched to avoid burning; when a number of
chambers are fitted on top of each other, the upper chambers may heat
up, so you should never touch the outer walls to avoid burning.
The three parameters to be set for baking are: the ceiling temperature, the floor
temperature, the baking time (time it takes the pizza to travel through the
baking chamber, which is directly dependent on the belt speed).
It is possible to store up to 100 different baking programs (20 in T64E) which
can be called up and/or modified at any time.
The different functions include "Eco Stand-by" or energy saving function with
the possibility to stop the belt that can be used during pauses in baking, while
the "Lock" function allows to block a series of operations so that the appliance
can be used also by untrained personnel.
The "Timer" (only T75E - TT96E - TT98E), allows the oven to be turned on at
different times for each day of the week.
The function: "Step" for discontinuous baking cycles is present. In addition,
only T75E - TT96E - TT98E, "Start-stop" function that activates the tape only
when the working temperature is reached.
SETTING LANGUAGE AND °C/°F:
To set language (Italian, English, French, German and Spanish etc.) see
section 3.2.15.
The control unit can be set to display temperature in Centigrade or in
Fahrenheit. To change setting see section 3.2.16.
3.2.1 DISLAY
T75E - TT96E - TT98E (fig.28)
The T75E is switched on by turning the switch (fig.14 part N) to position "1";
TT96E and TT98E are switched on by pressing a button (fig.14 part R).
The control panel lights up and, after a few seconds, during which the
Manufacturer's device is displayed, a screen like the one illustrated in fig. 28
appears.
NOTE:
If the emergency mushroom head button has been pressed
(fig.14 part O ) it will remain pressed in the safety position, and will not
allow the appliance to be turned back on again. To unlock the safety
button, turn it anti-clockwise
1A) set point temperature/ceiling temperature detected
1B) set point temperature/floor temperature detected
2) baking time (production processing in the oven)
3) explanatory status messages
4) indication of the oven status (idle/heating/baking)
5) working mode status (Manual, Program, Stand-by)
6) "Start Timer" status (not available for gas ovens)
7) "Conveyor belt Lock" status
8) "Step" status
9) "Lock" status
The oven's image appears at the center of the screen. The set-point
temperature is displayed in red above this image
NOTE:
if the display shows 1 temperature (or 4 temperatures on
TT96E or TT98E) at the switch on, see point 3.2.13 to set dual
temperature display.
To the right of the central image of the oven is an indication, in red, of the
baking time below which generic messages are indicated such as date, time,
oven model, oven status, etc ...inside a red label.
To the left of the screen starting from the top is the oven's status icon
represented by a gray lightning bolt indicating that the oven is off; it turns red
when the oven is heating and green when the oven is ready for baking. Below,
the working mode icon, is represented by 'M' If the manual mode is enabled,
by 'P ' If a baking program is enabled or the symbol of a money box if "Eco
standby" is enabled. The "Start Timer", "Conveyor belt Lock" and "Step"
status icon turn gray if the key is disabled and orange if the key is enabled. The
unlocked padlock icon indicates that the "Lock" key is disabled; it switches to
a closed padlock icon in orange if the key is enabled.
T64E (fig.29b)
The oven is turned on by setting the main switch (fig.29b part E) to position
"1" .
When turned on, the control panel will identify the following parameters:
A- ceiling temperature
B- floor temperature
C- set baking time
D- status display, for displaying the status of the equipment or of any
abnormalities detected
3.2.2 KEYBOARD
T75E - TT96E - TT98E (fig.29)
The buttons on the control panel are the following (its use will be
explained below:
10) -: decrease parameter
11) +: increase parameter
↑ and ↓ : "Up/Down" arrow keys
12)
13) Access to menu settings ("Menu")
14) Program management P ("Program")
15) Ok confirm
16) Delete, go back without confirming ("Return")
17) Ignition ("Start")
18) Off ("Stop")
19) Enable/disable Eco Standby function ("Stand-by")
20) Custom key ("Hotkey")
NOTE:
LCD not TOUCH SCREEN. If the display is pressed,
this can cause permanent damage which may stop the oven from
functioning properly.
T64E (fig.29b):
The keys on the right of the display, the functions of which will be
explained below, are as follows:
12) up arrow / +
13) down arrow / -
14) right arrow
15 ) left arrow
16) OK key
17) Start/Stop key
18) P/Hotkey programming key
19) Economy key
20) Lock key
3.2.3

STARTING THE OVEN

When switched on, the control panel will first show the initial screen
complete with the settings for the last baking operation carried out (T75E -
TT96E - TT98E fig.28, T64E Fig. 29b).
T75E - TT96E - TT98E
The operating mode icon indicates the previous baking mode manual
("M") or program set or ("P").
Press START (fig. 29 part 17 to operate the oven after a few seconds the
fan inside the oven and burner is activated. he temperature icon starts to
alternate the red set-point temperature displayed with the gauged white
temperature; the icon representing the flame status is colored, the status
icon turns red and the message bar concurrently indicates that the heating
process has begun. The configuration will hold until the oven reaches the
set point temperature.
The conveyor, by default is activated only when it reaches the working
temperature, as described in 3.2.11.
NOTE:
EVERY TIME THE EQUIPMENT MUST REACH THE
SET TEMPERATURE, BOTH AT SWITCH ON AND WHEN THE
TEMPERATURE CHANGES, THE ELECTRONIC ADJUSTMENT
NEEDS A FEW MINUTES TO CALIBRATE PERFECTLY TO
THIS. WAIT FOR THE TEMPERATURE TO STABILIZE BEFORE
COMMENCING TO LOAD THE OVEN, OTHERWISE THE
RESULTS WILL NOT BE EVEN AND THE BAKING QUALITY
WILL NOT BE OPTIMUM
NOTE:
If the START key is not pressed when the oven is
switched on, then after a limited period that can be set, the display will
enter energy-saving mode, turning black.
It is sufficient to press any key on the control unit to wake up the
display and make it operational.
NOTE:
The ceiling and floor temperatures are bound to one
another within a range of 20°C (T75E) or 15°C (TT96E and TT98E) to
guarantee that the baking temperatures are reached. It is possible to
release these two temperatures, at the operator's discretion, but
outside of a range of 20°C (T75E) or 15°C (TT96E and TT98E), it is no
longer guaranteed that the set temperature can be reached (see point
3.2.13).
T64E
The display (figure 29b part D) will show previous baking mode: manual
or preset program.
UK/4