Werbung
© Henckens seinen
part shows the signal background. In the
lower one the aspects are shown that a
control command will activate.
The accessory address of the signal A
is written to the address confi guration
variable relating to the fi rst function
output the signal is connected to. Up to
three addresses (A
are used for switching of signal aspects.
normal
fl ashing
address
A
1
1
func-
2
tion
3
normal
normal
outputs
normal
voie
voie
4
voie
signal
signal
signal
5
A
signal
A
signal
A
+1
signal
approach
approach
main
A
+1
signal
signal
signal
signal
A
+2
signal
A
+2
signal
Add-On Signals
The add-on signals are connected to the
4
4
Belgian light signals offer
pure speed signalling; route
information is not presented.
Speeds are presented by
illuminated fi gures or by
signs on the signals.
C
H
S
ontrolling
igH
ignalS
Main Signal
Qdecoders
offer
for both fl ashing and non
fl ashing
signals
confi gurations described in
the table below. The upper
, A
+1 and A
signal
signal
2
150
153
154
A
Signal
-
-
contre
normal
normal
-
voie
-
voie
voie
signal
-
signal
-
-
signal
control commands
DY
red
green
-
-
-
combined
main
approach
-
-
approach
GYH
main
signal
signal
signal
signal
signal
-
-
-
-
GYV
A2
A1
A0
A3
4
4
A4
Signal
normal
normal
Ampel
voie
voie
Licht
signal
signal
function outputs of the decoder that
follow the outputs used for the high signal
directly. A high signal can be combined
with any number of add-on signals.
mode
address
function
outputs
modes
A
addon
in
four
A
addon
The
add-on
associated with a proceed
aspect. If the add-on signal
is switched on while the
high signal shows either
signal
stop or shunting aspects
the high signals switches
to "proceed" automatically.
+2)
Changing the high signal
signal
aspect to stop will switch
off the add-on signal too.
151
152
Mode 218: The disturbed
155
156
signal is switched on and
off using commands of an
accessory address that is written to the
adress CV of any function output the signal
is connected to (described in more detail
in the example „Haupt- / Vorsignalkombi-
contre
contre
contre
nationen" on page 12).
voie
voie
voie
An Example
signal
signal
signal
A small high signal and a no fl ashing
high signal with speed announcement
are to control using a Z1-8 decoder with
Signal
RW
DG
be controlled by commands of accessory
combined
approach
combined
main
combined
main
address 1, the second one using accessory
signal
signal
signal
signal
signal
signal
address 5. Address 4 is used for the speed
DY
announcement.
Connect the signals to the decoder and
A2
A2
A2
A1
A1
A1
program
A0
A0
A0
according to the following table. The values
A3
A3
A3
given in grey do not need programming
4
A4
A4
A4
normal
voie
signal
Basis
Standard
Alleskönner
approach
main
signal
signal
approach
approach
206
main
main
signal
signal
signal
signal
A
A
1
addon
4
1
control commands
off
4
4
on
signals
are
contre
voie
signal
extension. The fi rst signal shall
combined
signal
A2
A1
the
confi guration
A0
A3
A4
contre
voie
signal
base class
contre
contre
standard class
voie
voie
all-in-one class
signal
signal
combined
signal
A2
218
combined
combined
A1
signal
signal
A0
A3
dark
A4
signal
A2
A2
A1
A1
A0
A0
signal is on
A3
A3
A4
A4
signal is off
© Henckens seinen
variables
85
Werbung
