Contents English - OMCN ROLL R6 Betriebsanleitung

en 44 | ROLL R6 M |

Contents English

1. Symbols used
1.1 In the documentation
1.1.1 Warning notices -
Structure and meaning
1.1.2 Symbols in this documentation
1.2 On the product
1.2.1 Product information
1.2.2 Warning indications
2. User information
2.1 Important notes
2.2 Safety instructions
2.3 Electromagnetic compatibility (EMC)
3. Product description
3.1 Intended use
3.2 Prerequisites
3.3 Scope of delivery
3.4 Special accessories
3.5 ROLL R6 M
4. Commissioning
4.1 Unpacking
4.1.1 Machine movement
4.1.2 Fastening to the floor
4.2 Cone holder assembly
4.3 Fitting wheel guard
4.4 Fitting monitor
4.5 Electrical connection
4.6 Checking the direction of rotation
4.7 Calibration of ROLL R6 M
5. Fitting and removing the flange
5.1 Removing flange
5.2 Fitting flange
6. Fitting and removing the wheel
6.1 Securing the wheel
6.2 Removing the wheel
7. Operation
7.1 Start page
7.2 Monitor display
7.2.1 Status bar
7.2.2 Display field
7.2.3 Soft key bar
7.2.4 EXIT key
7.3 Control panel
|
1 695 600 694 2016-09-28
46 8. Program structure
46 8.1 Wheel balancing
8.2 Settings and service
46 8.2.1 Calibration
46 8.2.2 Settings
46 8.2.3 User-defined settings
46 8.3 Rim data
47
9. Balancing a wheel
48 9.1 Balancing programs
48 9.2 Manual selection of the balancing program
48 9.3 Automatic selection of the balancing program 65
48 9.3.1 Standard balancing program
9.3.2 Alu3 balancing program
48 9.3.3 Alu2 balancing program
48 9.4 Entering of wheel data for standard programs 68
48 9.4.1 Automatic measurement of the Distance
49 and Diameter (with Easyfit®)
50 9.4.2 Measuring the Width
51 9.5 Entering of wheel data for non-standard
programs
52 9.5.1 Automatic measurement of Distance
52 and Diameter
52 9.5.2 Measuring the Width
53 9.6 Measuring unbalance
54 9.7 Application of the balancing weights
54 9.7.1 Spring-clip weights and adhesive
55 weights for standard programs
56 (without Easyfit®)
57 9.7.2 Spring-clip weights and adhesive
57 weights for non standard programs
(with Easyfit®)
58 9.7.3 Splitting the balancing weights (Split
58 program)
58 9.8 Fixing of spring-clip weights
9.9 Fixing the adhesive weights
59 9.9.1 Applying the adhesive weights using
59 the electronic calliper gauge
59 (with Easyfit®)
9.9.2 Applying the adhesive weights using the
60 internal clamp (without Easyfit®)
60 9.9.3 Fixing the adhesive weights with
60 external clamp
60
60 10. Unbalance minimization
60
60 11. Faults
60
61
61
61
61
62
62
63
64
64
65
65
66
67
68
69
69
69
70
70
71
71
71
72
72
73
73
73
74
75
77
OMCN spa