Danfoss VLT AutomationDrive FC 301 Programmierhandbuch Seite 282

Parameterlisten
Para Parameterbeschreibung
meter
num
mer
17-74 Position Offset
17-75 Position Recovery at Power-up
17-76 Position Axis Mode
17-77 Position Feedback Mode
17-8* Position Homing
17-80 Homing Function
17-81 Home Sync Function
5 5
17-82 Home Position
17-83 Homing Speed
17-84 Homing Torque Limit
17-85 Homing Timout
17-9* Position Config
17-90 Absolute Position Mode
17-91 Relative Position Mode
17-92 Position Control Selection
17-93 Master Offset Selection
17-94 Rotary Absolute Direction
5.3.18 18-** Datenanzeigen 2
Para Parameterbeschreibung
meter
num
mer
18-3* Analog Readouts
18-36 Analogeingang X48/2 [mA]
18-37 Temp. Eing. X48/4
18-38 Temp. Eing. X48/7
18-39 Temp. Eing. X48/10
18-5* Active Alarms/Warnings
18-55 Active Alarm Numbers
18-56 Active Warning Numbers
18-6* Inputs & Outputs 2
18-60 Digital Input 2
5.3.19 30-** Spezielle Merkmale
Para Parameterbeschreibung
meter
num
mer
30-2* Adv. Start Adjust
30-20 Startmoment hoch
30-21 High Starting Torque Current [%]
30-22 Locked Rotor Protection
30-23 Locked Rotor Detection Time [s]
30-24 Locked Rotor Detection Speed Error [%]
30-8* Kompatibilität (I)
30-80 D-Achsen-Induktivität (Ld)
30-81 Bremswiderstand (Ohm)
280
®
VLT AutomationDrive FC 301/302
Werkseinstellung
0 CustomReadoutUnit2
[0] Aus
[0] Linear Axis
[0] Relative
[0] No Homing
[0] 1st time after power
0 N/A
150 RPM
160 %
60 s
[0] Standard
[0] Target Position
[0] No operation
[0] Absolute Enabled
[0] Shortest
Werkseinstellung
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
0 N/A
Werkseinstellung
ExpressionLimit
ExpressionLimit
ExpressionLimit
ExpressionLimit
25 %
ExpressionLimit
ExpressionLimit
Danfoss A/S © 08/2017 Alle Rechte vorbehalten.
4 Parame- Nur FC 302 Ändern
tersätze während
des
Betriebs
All set-ups FALSE
All set-ups TRUE
All set-ups TRUE
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
All set-ups FALSE
4 Parame- Nur FC 302 Ändern
tersätze während
des
Betriebs
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups TRUE
All set-ups FALSE
4 Parame- Nur FC 302 Ändern
tersätze während
des
Betriebs
All set-ups x TRUE
All set-ups x TRUE
All set-ups x TRUE
All set-ups x TRUE
All set-ups x TRUE
All set-ups x FALSE
1 set-up TRUE
Konver- Daten
tierungsi typ
ndex
0 Int32
- Uint8
- Uint8
- Uint8
- Uint8
- Uint8
0 Int32
67 Int16
0 Uint16
-1 Uint16
- Uint8
- Uint8
- uint8
- uint8
- uint8
Konver- Daten
tierungsi typ
ndex
-3 Int32
0 Int16
0 Int16
0 Int16
0 Uint16
0 Uint16
0 Uint16
Konver- Daten
tierungsi typ
ndex
-2 Uint16
-1 Uint32
- Uint8
-2 Uint8
-1 Uint32
-6 Int32
-2 Uint32
MG33MN03