Presentation; Product Description; Intended Use - Dover Vsg Rav.td808 Übersetzung Der Originalanleitung

TABLE OF
CONTENTS
2

PRESENTATION

2.1

PRODUCT DESCRIPTION

• Product name:
• Product description:
2.2

INTENDED USE

The CCD system is a piece of equipment intended for the full detection of the characteristic angles of heavy vehicles and trucks.
Angle detection is carried out by four sensors with microprocessor technology and an infrared measuring and data transmission
system (without using cable connections between the sensors).
Data transmission from the measuring heads is VIA RADIO by means of Bluetooth-compatible modules.
Use the equipment (CAT II) in the following operating range:
• Internal use
• Temperature between 32°F (0°C) and 104°F (40°C)
• Relative humidity from 30% to 70%
• Maximum altitude 9842Ft (3000m) above sea level (asl)
• During the operation and maintenance of this machine it is absolutely essential to comply with all the safety and accident-prevention
regulations in force and with the European Directives 89/686/EEC, UNI EN ISO 20345, UNI EN ISO 13688: 2013, EN 388 and EN 420.
• The equipment must only be used by authorised and adequately trained personnel.
• It is not permitted to attach very heavy objects (weighing more than 15 kg) on the console (e.g.: the turntables).
• Do not use the equipment in places where persistent conductive dust is present (pollution degree equal to or greater than 3).
• Do not install or store the device in outdoor areas or in areas exposed to climatic conditions such as direct sunlight, wind, rain
or temperatures below zero.
• When operating the device outside the specified conditions, there is a risk that its safety and operation could be compromised.
• Always check that the equipment is positioned in such a way that the electrical outlet is accessible.
• The equipment must always be on a flat and horizontal surface.
• If the power cord is damaged, it must be replaced by the manufacturer, an authorised dealer or qualified personnel to avoid
danger.
• It is important to keep this manual for future use. It is an integral part of the equipment. For this reason, it should always be
attached to the equipment itself.
WARNING
• For safety reasons, insert the cable in an earthed AC (Alternate Current) socket.
Risk of fire and explosion! To reduce this risk, the machine must be used only in places where there is no risk of fire or explosion.
•
This product must be installed and used only within licensed workshops.
Risk of electric shock! Never open the system. For continuous protection against electric shock, the console must be connected
•
to a reliable earthing system. Do not remove the earthing connection. If the socket in the facility does not have an earthing
connection, do not modify the connection plug.
• This equipment must only be used for the purpose for which it is expressly designed.
VSG ITALY S.R.L. disclaims all liability for persons, animals and property caused by misuse of the machine.
• Accessories and spare parts must be installed by VSG ITALY S.R.L. authorised personnel and only original accessories and spare
parts must be used. It is also not permitted, in any way, to replace batteries using non-original batteries. It is necessary to use
only the manufacturer's original batteries on the measuring heads.
• The removal or modification of safety devices or of warning signs placed on the machine can cause serious danger and constitutes
a violation of the European safety standards.
• Before carrying out any maintenance on the system, it is necessary to disconnect the power supply. In case of doubt, do not
improvise but rather contact VSG ITALY S.R.L. technical support to receive instructions and carry out the necessary procedures
under safe conditions.
• The operator must wear safety footwear to avoid damage to their feet, caused by the accidental falling of clamps or measuring
heads. Use footwear with certified protection according to the EN ISO 20345 standard.
• The operator must wear protective gloves when handling the clamps. Use gloves according to the EN 388 standard.
• Prevent unauthorised personnel from approaching the wheel aligner during use.
• Use only the supplied cables. In the event of breakage or a fault, consult qualified service personnel.
• Never try to use the equipment if it is damaged, if it works incorrectly, if it has been partially disassembled and if any components,
including cable and plug, are missing or damaged.
RAV.TD808-RAV.TD806 / ROT.SP808-ROT.SP806 / SPA.ART98-SPA.ART86
TRUCK WHEEL ALIGNERS
CCD Truck Wheel Aligner
2015-M362-0 EN-5