Werbung
Have damaged parts repaired by qualified specialist
personnel.
Only use the chainsaw and accessories in accord-
ance with these instructions. Take into account the
working conditions and the work to be performed.
Using power tools for operations other than those in-
tended can lead to hazardous situations.
■ Regularly check the chain brake for proper func-
tioning (front hand guard, see Fig. B).
■ Check the guide rail to make sure it is mounted cor-
rectly.
■ Check that the saw chain is properly tensioned.
Follow the instructions for lubrication, chain ten-
sioning and replacing accessories. An improperly
tensioned or lubricated chain can break or increase
the risk of kick-back.
■ Keep cutting tools sharp and clean. Sharpen regu-
larly and replace worn parts in good time. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
■ Check that the throttle and the throttle interlock
move easily. The throttle lever must spring back to
the starting position.
■ Check that there is enough fuel and chain lubricat-
ing oil in the tank.
■ Check that the handles are clean, dry and free from
oil and dirt.
■ Never carry out the work alone. In an emergency,
someone must be nearby.
■ Only use the chainsaw when standing on firm, safe
and level ground. Avoid abnormal postures. Slip-
pery ground or unstable standing surfaces (e.g.
on a ladder) can cause loss of balance or loss of
control of the chainsaw. Keep proper footing and
balance at all times. This will allow you to better
control the chainsaw in unexpected situations.
■ Do not work with the chainsaw in a tree. There is a
risk of injury when operating in a tree.
■ Never saw above shoulder height.
■ Always hold the chainsaw with your right hand on
the rear handle and your left hand on the front han-
dle (see fig. D). Holding the chainsaw using the op-
posite grip increases the risk of injuries and must
be avoided.
■ Keep all body parts away from the saw chain when
the chainsaw is running. Before starting the chain-
saw, ensure that the saw chain is not touching an-
ything. When working with a chainsaw, a moment
of carelessness can result in clothing or body parts
being caught by the saw chain.
■ Switch off the chainsaw immediately if you notice
any noticeable changes in the device's behaviour.
■ If the chainsaw has come into contact with stones,
nails or other hard objects, stop the engine imme-
diately and check the saw chain and guide rail for
damage.
34 | GB
■ Do not drop the chainsaw, do not hit it against ob-
stacles and never use the guide rail as a lever.
■ Only saw in wood with the chainsaw.
■ When cutting a branch that is under tension, expect
it to spring back. If the tension in the wood fibres is
released, the tensioned branch can hit the operator
and/or wrest the chainsaw from control.
■ Be especially careful when cutting undergrowth and
young trees. The thin material can get caught in the
saw chain and hit you or throw you off balance.
6.7 Vibrations
m WARNING
Avoid the risks associated with vibration, e.g. the risk
of white finger syndrome (circulatory disorders).
Raynaud's syndrome is a vascular disease that caus-
es the small blood vessels on the fingers and toes to
cramp in spasms. The symptoms include: Numbness,
loss of sensitivity, tingling, itching, pain, decrease in
strength, change of colour or condition of the skin.
The affected areas are no longer supplied with suf-
ficient blood and therefore appear extremely pale.
The frequent use of vibrating tools can cause nerve
damage in people whose circulation is impaired (e.g.
smokers, diabetics). If you notice unusual adverse
effects, stop working immediately and seek medical
advice. For long-term and regular users, it is there-
fore recommended that you keep a close eye on the
condition of your hands and fingers. Observe the fol-
lowing information to reduce hazards:
■ Keep your body warm, especially your hands, es-
pecially in cool weather.
■ Take regular breaks and move your hands to pro-
mote circulation.
■ Limit the use of high-vibration tools per day and
spread them out over several days. Make a work
plan that limits the vibration load.
■ Ensure that the device vibrates as little as possible
through regular maintenance and fixed parts on the
device. Replace worn components immediately.
■ Change your working position regularly.
■ If the machine is to be used or operated frequently,
you should contact your specialist dealer and request
anti-vibration accessories (handles) if applicable.
6.8 Safety functions of the chainsaw (Fig. 1)
■ The FRONT HAND GUARD (1) protects the left
hand of the operating person should it slip off the
front handle while the chainsaw is running.
■ The REAR HAND GUARD (12) protects the right
hand from contact with a discarded or broken saw
chain.
■ The CHAIN BRAKE is a safety function for mini-
mising injuries from kick-backs by stopping a run-
ning saw chain in milliseconds. It is activated by the
front hand guard in the event of a kick-back.
www.scheppach.com
Werbung
