Detect Data Carriers; Read/Write Data Carrier; Operation - Balluff BIS U-4A7-082-01C-07-S4 Betriebsanleitung

BIS U-4A7-082- _1C-07-S4
Industrial RFID system - Read/write head
7
Startup and operation (continued)
7.2.4

Detect data carriers

The S button in the S
tart can
used to create a data carrier list that lists the data carriers
that are within the detection range of the selected device.
1. Select the S tab in the action area.
can
2. Select device via the radio button in the info area.
3. Click on S
tart
⇒ Data carriers in the detection range of the selected
device are detected and entered in the list.
The data carrier list contains the following information:
– ePc/tid: EPC or TID of the data carrier
– rSSi: Highest RSSI value measured when the data
carrier was detected
– c : Counts how often the data carrier was detected
ount
in cyclical operation
– c : Counts the detection intervals in cyclical
ycLeS

operation

What to read
In the w selection area, you can select which
hat to read
data (EPC or TID) should be entered in the list when
detecting the data carriers.
Right-click on a data carrier in the list to switch
directly to the r
interactions with the data carrier can be
performed.
Scan
In the S selection area, you can define the operating
can
mode with which the data carrier detection is performed.
S
ynchronouSLy SingLe Scan
Via the S button, detection of the data carriers is
tart
carried out once. The data carrier list is cleared before
each operation and filled with the new result.
S
ynchronouSLy rePeated Scan
The S button starts the data carrier detection and
tart
repeats it cyclically at the specified interval (milliseconds).
In the process, the data carrier list is continuously updated.
New data carriers are added to the list and colored green.
Data carriers that have left the detection range of the
antenna are colored red. Cyclical detection continues until
it is stopped via the S button.
toP
24 english
tab of the action area can be
tab. There, further
/w
ead rite
7.2.5

Read/write data carrier

The r tab provides the functions for reading out
/
ead write
and writing to data carriers. The desired action can be
started via the r and w
ead rite
data carrier can be processed, it must be detected in the
S tab.
can
Memory area via which the TAG is to be identified
The EPC and TID of the data carrier can be used to select
an individual data carrier. An individual data carrier can be
selected via the respective drop-down list.
Right-click on a data carrier in the list to switch
directly to the r
/w
ead
interactions with the selected data carrier can
be performed.
a
cceSS PaSSword
By selecting the a
cceSS PaSSword
appears in which an access password can be entered.
This function is only intended for data carriers that are
secured by an access password.
Which memory area should be processed?
Selection of the memory area to be read or written to. The
ePc, tid, r and u
eServed Ser data
selection. Details on the memory areas and their size can
be found in the data sheet of the data carriers used.
For the ePc and tid data, the
fixed.
For direct access to the memory banks of ePc, tid,
r as well as the u
eServed Ser data
and L (number of bytes) can be defined via the input
ength
fields provided.
Memory Read Write
area
ePc Yes Yes
Yes No
tid
Yes Yes
u
Ser data
ePc Yes Yes
bank
tid Yes No
bank
Tab. 7-1: Memory areas
buttons. Before an individual
tab. There, further
rite
check box, an input field
areas are available for
and are
Start addreSS Length
area, the S
tart addreSS
Start Length
address
Fixed Parameters
Fixed Parameters
field
S L
tart ength
addreSS
field
S L field
tart ength
addreSS
field
S L field
tart ength
addreSS
field